Nissan Sentra manuals

Nissan Sentra B18 (2020-2025) Service Manual: Dtc Diagnosis Procedure

Nissan Sentra B18 (2020-2025) Service Manual / Driver Information & Multimedia / Sonar System :: Dtc/circuit Diagnosis / B2720 Corner Sensor [rl] / Dtc Diagnosis Procedure

DTC Diagnosis Procedure

  1. DETERMINE MALFUNCTION TYPE

    1. CONSULT

      1. Ignition switch ON.

      2. Select “Self Diagnostic Result” mode of “SONAR”.

      3. Check DTC.

    Is DTC B2720–60, 61, 62, 63, 65, 66, 67, 68, 83 or 92 detected?

    YES >>

    66 – GO TO 2.

    YES >>

    60, 61, 62, 63, 65, 67, 68, 83 or 92 – GO TO 5.

    NO >>

    Refer to Intermittent Incident.

  2. CHECK REAR SONAR SENSOR LH OUTER SIGNAL CIRCUIT FOR OPEN OR SHORT TO GROUND

      1. Ignition switch OFF.

      2. Disconnect sonar control unit and rear sonar sensor LH outer connectors.

      3. Check continuity between sonar control unit connector and rear sonar sensor LH outer connector.

        Sonar control unit

        Rear sonar sensor LH outer

        Continuity

        Connector

        Terminal

        Connector

        Terminal

        B87

        22

        B402

        2

        Yes

      4. Check continuity between sonar control unit connector and ground.

        Sonar control unit

        —

        Continuity

        Connector

        Terminal

        B87

        22

        Ground

        No

    Is the inspection result normal?

    YES >>

    GO TO 3.

    NO >>

    Repair or replace harness or connectors.

  3. CHECK REAR SONAR SENSOR LH OUTER GROUND CIRCUIT FOR OPEN

      1. Ignition switch OFF.

      2. Check continuity between sonar control unit connector and rear sonar sensor LH outer connector.

        Sonar control unit

        Rear sonar sensor LH outer

        Continuity

        Connector

        Terminal

        Connector

        Terminal

        B87

        14

        B402

        1

        Yes

    Is the inspection result normal?

    YES >>

    GO TO 4.

    NO >>

    Repair or replace harness or connectors.

  4. CHECK REAR SONAR SENSOR LH OUTER SIGNAL

      1. Connect sonar control unit and rear sonar sensor LH outer connectors.

      2. Ignition switch ON.

      3. Check signal between the terminals of sonar control unit connector.

        Sonar control unit

        Condition

        Reference value

        Connector

        (+)

        (–)

        Terminal

        Terminal

        B87

        22

        14

        Sensor signal input

    Is the inspection result normal?

    YES >>

    Replace sonar control unit. Refer to Removal and Installation.

    NO >>

    Replace rear sonar sensor LH outer. Refer to Removal and Installation.

  5. PERFORM DTC CONFIRMATION PROCEDURE AGAIN

    1. CONSULT

      1. Ignition switch ON.

      2. Erase DTC.

      3. Select “Self Diagnostic Result” mode of “SONAR”.

      4. Check DTC.

    Is DTC B2720–60, 61, 62, 63, 65, 67, 68, 83, or 92 detected?

    YES >>

    Replace rear sonar sensor LH outer. Refer to Removal and Installation.

    NO >>

    Inspection End.

Dtc Confirmation Procedure
DTC Confirmation Procedure DTC CONFIRMATION PROCEDURE CONSULT Ignition switch ON. ...

B2721 Center Sensor [rl]
...

Other materials:

P0712 Transmission fluid temperature sensor A
DTC Logic DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition Possible causes P0712 FLUID TEMP SENSOR A (Transmission Fluid Temperature Sensor A Circuit Low) The CVT fluid temperature identified by the TCM is 1 ...

Push-Button Ignition Switch Circuit
Component Function Check Component Function Check CHECK FUNCTION CONSULT Ignition switch ON Select “Push SW” in “Data Monitor” mode of “HANDS FREE MO ...

Bsw Indicator
Removal and Installation Removal and Installation REMOVAL Note: LH shown; RH similar Remove front door finisher. Refer to Removal and Installation. Using a suitable tool, release clips from door mirror corner finisher (3) in the sequence shown. ...

© 2014-2026 Copyright www.nisentra.com