Nissan Sentra B18 (2020-2025) Service Manual: Configuration (bcm)

Nissan Sentra B18 (2020-2025) Service Manual / Electrical & Power Control / Body Control System :: Basic Inspection / Inspection and Adjustment / Configuration (bcm)

Description

Description

Vehicle specifications need to be written with CONSULT, because it is the not automatically write after replacing the BCM.

Configuration as follows:

Function			Description
Nissan Sentra Vehicle Configuration	Before ECU Replacement		Reads the Nissan Sentra vehicle configuration of the current BCM. Saves the read vehicle configuration.
	After ECU Replacement	FAST linked	Note: This item is displayed, but cannot be used.
	After ECU Replacement	Manual selection	Writes the Nissan Sentra vehicle configuration with manual selection.
Operation Log Selection			Writes the read Nissan Sentra vehicle configuration.

CAUTION:

When replacing the BCM, always perform “Re/programming, Configuration” with CONSULT, or not doing so, the BCM control function may not operate normally.

After installing a new BCM service part, if the Intelligent Key UNLOCK button is pressed before performing the configuration with CONSULT, certain BCM configuration parameters will be permanently locked in the default setting; one of these parameter is remote engine start.

Complete the procedure of “Re/programming, Configuration” in order.

Configuration is different for each Nissan Sentra vehicle model. Confirm configuration of each vehicle model.

Never save vehicle configuration to the BCM used by other cars.

If you set incorrect Nissan Sentra vehicle configuration, incidents might occur.

It is not necessary to register Intelligent Keys to a new BCM.

Before pairing of the BCM and Intelligent Key unit, always write the BCM configuration, or not doing so, the BCM control function will not operate normally.

Work Procedure

Work Procedure

WRITING MODE SELECTION
1. CONSULT
  
  Select “Re/programming, Configuration” .
When writing saved data>>
GO TO 2.
When writing manually>>
GO TO 3.
WHEN WRITING SAVED DATA
1. CONSULT
  
  Select the operation according to the CONSULT screen.
YES >>
GO TO 4.
WHEN WRITING MANUALLY
1. CONSULT
  1. Select “Manual selection”.
  2. Identify the correct model and configuration list. Refer to Configuration List.
  3. Confirm and/or change setting value for each item.
    
    CAUTION:
    
    Thoroughly understand the Nissan Sentra vehicle specification. ECU control will not operate normally if the setting is not correct.
    
    Note:
    - If items are not displayed, select “Next”.
    - Each item differs for each Nissan Sentra vehicle depending on specification.
  4. Select “Next”.
  5. Select “OK”.
    
    CAUTION:
    
    Make sure to select “OK” even if the indicated configuration of a brand new BCM is the same as the desirable configuration. If not, configuration, which is set automatically by selecting the Nissan Sentra vehicle model, cannot be memorized.
  6. Check that the configuration has been successfully written and select “End”.
YES >>
GO TO 4.
OPERATION CHECK
1. Confirm that each function controlled by the BCM operates normally.
YES >>
Work End.

Configuration List

Configuration list

CAUTION:

Thoroughly read and understand the vehicle specification. Incorrect settings may result in abnormal control of ECU.

SETTING ITEM		NOTE
Items	Setting value	NOTE
Combination switch type	MODE2 ⇔ MODE3	MODE2: Without ALS MODE3: With ALS
Exterior lamp setting	MODE2	—
Daytime running light	TRUE ⇔ FALSE	TRUE: With daytime running light FALSE: Without daytime running light
Paddle shift	FALSE	—
Sport mode switch type	MODE1 ⇔ MODE2	MODE1: Without drive sport mode switch MODE2: With drive sport mode switch
Stop/start system	MODE1 ⇔ MODE3	MODE1: Without idle start/stop system MODE3: With idle start/stop system
Recommended reference air pressure (rear wheel)	MODE1 ⇔ MODE2	MODE1: 31 psi (215 kPa) MODE2: 28 psi (196 kPa)
TPMS ON/OFF function	TRUE ⇔ FALSE	TRUE: With TPMS ON/OFF function FALSE: Without TPMS ON/OFF function
TPMS	TRUE	—
Easy fill function	TRUE	—
Nissan Sentra Vehicle security alarm	TRUE ⇔ FALSE	TRUE: With Nissan Sentra vehicle security system FALSE: Without vehicle security system
Scandinavian runnings lights	TRUE ⇔ FALSE	TRUE: With Scandinavian running light FALSE: Without Scandinavian running light
HAZARD_WITH_CRASH_CF	TRUE ⇔ FALSE	TRUE: With auto hazard function FALSE: Without auto hazard function
CRASH_DETECTION_CF	MODE1 ⇔ MODE2	MODE1: RKE enabled with ignition switch OFF MODE2: RKE always enabled
ENHANCE_LO_ON_THRESH	MODE1 ⇔ MODE2	MODE1: 825 lux MODE2: 1250 lux
ALS_TRAFFIC_LIGHT	TRUE ⇔ FALSE	TRUE: With ALS traffic light FALSE: Without ALS traffic light
AV control unit	TRUE ⇔ FALSE	TRUE: With AV control unit FALSE: Without AV control unit
TCU	TRUE ⇔ FALSE	TRUE: With telematics FALSE: Without telematics
High beam assist / ALH setting	MODE1 ⇔ MODE2	MODE1: Without high beam assist system MODE2: With high beam assist system
ADAS control unit	TRUE ⇔ FALSE	TRUE: With ADAS control unit FALSE: Without ADAS control unit
Door lock/unlock permission when ignition is ON	MODE2 ⇔ MODE3	MODE2: RKE enabled with engine stopped MODE3: RKE always enabled

⇔: Items which confirm Nissan Sentra vehicle specifications

Additional Service When Replacing Control Unit (bcm)

Description Description CAUTION: Be sure to perform the configuration saving and writing or reregistration when replacing the BCM. When r ...

Shipping Mode Cancel Operation

...

Other materials:

Forward-facing child restraint installation using the seat belts
WARNING The three-point seat belt with Automatic Locking Retractor (ALR) must always be used when installing a child restraint in the Nissan Sentra. Failure to activate and use the ALR mode will prevent the child restraint from being properly secured. An unsecured or unstable restraint may tip ...

P17f2-07 Cvt Judder (t/c Inspection)
Dtc Description DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection conditi ...

Precaution for Supplemental Restraint System (srs) "air Bag" and "seat Belt Pre-Tensioner"
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and fron ...