Nissan Sentra Service Manual: C1716, C1717, C1718, C1719 Transmitter (pressure data)
DTC Logic
NOTE:
The Signal Tech II Tool (J-50190) can be used to perform the following functions. Refer to the Signal Tech II User Guide for additional information.
- Activate and display TPMS transmitter IDs
- Display tire pressure reported by the TPMS transmitter
- Read TPMS DTCs
- Register TPMS transmitter IDs
DTC DETECTION LOGIC
| DTC | Display Item | Malfunction detected condition | Possible causes |
| C1716 | [PRESSDATA ERR] FL | Malfunction in the tire pressure data from the front LH wheel transmitter. |
|
| C1717 | [PRESSDATA ERR] FR | Malfunction in the tire pressure data from the front RH wheel transmitter. | |
| C1718 | [PRESSDATA ERR] RR | Malfunction in the tire pressure data from the rear RH wheel transmitter. | |
| C1719 | [PRESSDATA ERR] RL | Malfunction in the tire pressure data from the rear LH wheel transmitter. |
DTC CONFIRMATION PROCEDURE
1.PERFORM SELF DIAGNOSTIC RESULT
With CONSULT
- Turn the ignition switch ON.
- Check the tire pressure for all wheels and adjust to the specified value. Refer to WT-54, "Tire Air Pressure".
- Perform “SELF DIAGNOSTIC RESULT”.
Is DTC “C1716”, “C1717”, “C1718”, or “C1719” detected? YES >> Proceed to WT-30, "Diagnosis Procedure".
NO >> Inspection End.
Diagnosis Procedure
NOTE:
The Signal Tech II Tool (J-50190) can be used to perform the following functions. Refer to the Signal Tech II User Guide for additional information.
- Activate and display TPMS transmitter IDs
- Display tire pressure reported by the TPMS transmitter
- Read TPMS DTCs
- Register TPMS transmitter IDs
1.CHECK TIRE PRESSURE
Check the air pressure of all wheels. Refer to pressure observed during “DTC CONFIRMATION PROCEDURE”.
Is the inspection result normal? YES >> Replace the DTC-detected malfunctioning transmitter. Refer to WT-50, "Removal and Installation".
NO >> GO TO 2.
2.CHECK TIRE PRESSURE SIGNAL
With CONSULT
- Perform transmitter ID registration for all wheels. Refer to WT-22, "Work Procedure".
- Drive for 3 minutes at a speed of 40 km/h (25 MPH) or more, then drive normally for 10 minutes.
- Stop the vehicle.
- On “DATA MONITOR” select “AIR PRESS FL”, “AIR PRESS FR”, “AIR PRESS RR” and “AIR PRESS RL”.
- Within 5 minutes after vehicle is stopped, read the values displayed on CONSULT.
Are tire pressures displayed as 438.6 kPa (4.47 kg/cm2, 63.6 psi)? YES >> Replace transmitter for the tire that displayed pressure as 438.6 kPa (4.47 kg/cm2, 63.6 psi).
Refer to WT-50, "Removal and Installation".
NO >> Perform “DTC CONFIRMATION PROCEDURE” again. Refer to WT-30, "DTC Logic".
C1708, C1709, C1710, C1711 Transmitter (no data)
DTC Logic
NOTE:
The Signal Tech II Tool (J-50190) can be used to perform the following
functions. Refer to the Signal Tech II
User Guide for additional information.
Activate and display TPMS ...
C1729 Vehicle speed signal
DTC Logic
NOTE:
The Signal Tech II Tool (J-50190) can be used to perform the following
functions. Refer to the Signal Tech II
User Guide for additional information.
Activate and display TPMS ...
Other materials:
General Precaution
WARNING:
When replacing fuel line parts, be sure to observe the following.
Put a “CAUTION: FLAMMABLE” sign in the work area.
Be sure to work in a well ventilated area and have a CO2 fire
extinguisher.
Do not smoke while working on the fuel system. Keep open flames
and sparks ...
Power supply and ground circuit
Combination meter
Combination meter : diagnosis procedure
Regarding Wiring Diagram information, refer to MWI-28, "Wiring Diagram".
1.Check fuses
Check that the following fuses are not blown.
Is the fuse blown?
YES >> Replace the blown fuse after repairing the affected circu ...
Vehicle information
Body exterior paint color
M = Metallic, S = Solid, 2S = Solid and Clear, 2P = 2-Coat Pearl, 3P = 3-Coat
Pearl, PM = Pearl Metallic, t = Primerless Diamond Clear
coat, Black is solvent based, all others are water based. ...
