Nissan Sentra B18 (2020-2025) Service Manual / Steering / Steering Control System :: Dtc/circuit Diagnosis / C1623-87 Ecm System

Nissan Sentra B18 (2020-2025) Service Manual: C1623-87 Ecm System

Dtc Description

DTC Description

DTC DETECTION LOGIC

DTC No.	CONSULT screen terms (Trouble diagnosis content)	DTC detection condition
C1623-87	ECM system (Engine control module system)	Diagnosis condition	When ignition switch is ON.
		Signal (terminal)	CAN communication signal
		Threshold	When a malfunction is detected in ECM.
		Diagnosis delay time	2 seconds or more

POSSIBLE CAUSE

CAN communication line
ECM
EPS control unit

FAIL-SAFE

Normal control

Confirmation Procedure

PRECONDITIONING
1. If “Confirmation Procedure” has been previously conducted, always place the ignition switch OFF and wait at least 10 seconds before conducting the next test.
>>
GO TO 2.
DTC REPRODUCTION PROCEDURE
1. CONSULT
  1. Ignition switch ON.
  2. Select "Self Diagnostic Result" mode of “EPS/DAST 3”.
Is DTC “C1623-87” detected?
YES >>
Proceed to diagnosis procedure. Refer to DTC Diagnosis Procedure.
NO >>
To check malfunction symptom before repair: Refer to Intermittent Incident.
NO >>
Confirmation after repair: Inspection End.

Dtc Diagnosis Procedure

DTC Diagnosis Procedure

PERFORM SELF DIAGNOSTIC RESULT
1. CONSULT
  1. Ignition switch ON.
  2. Select "Self Diagnostic Result" mode of “ENGINE”.
Is any DTC detected?
YES >>
Check the DTC. Refer to DTC Index.
NO >>
GO TO 2.
CHECK CONNECTOR AND TERMINAL
1. 1. Ignition switch OFF.
  2. Disconnect ECM harness connector.
  3. Disconnect EPS control unit harness connector.
  4. Check the connector for disconnection or looseness.
  5. Check the pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES >>
GO TO 3.
NO >>
Repair or replace harness, connector, or terminal, securely lock the connector.
PERFORM SELF DIAGNOSTIC RESULT
1. CONSULT
  1. Connect ECM harness connector.
  2. Connect EPS control unit harness connector.
  3. Ignition switch ON.
  4. Erase "Self Diagnostic Result" mode of "EPS/DAST 3".
  5. Ignition switch OFF and wait for at least 10 seconds.
  6. Ignition switch ON.
  7. Select "Self Diagnostic Result" mode of “EPS/DAST 3”.
Is DTC “C1623-87” detected?
YES >>
EPS control unit is malfunctioning. Replace steering gear assembly. Refer to Removal and Installation.
NO >>
Inspection End.

 C1621-87 Bcm System

Dtc Description DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C1621-87 BCM system (Body control module sys...

 C1624-00 Signal Connector

Dtc Description DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C1624-00 Signal connector (Signal connector)...

Other materials:

Intelligent Key System
System Diagram System Diagram System Description System Description Signal name Input Output Description ...

Road Wheels & Tires. Ecu Diagnosis Information. Bcm, Intelligent Key Unit. List of Ecu Reference
Bcm, Intelligent Key Unit. List of Ecu Reference List of Ecu Reference List of ECU Reference ECU Reference BCM Values on the Di ...

Basic Inspection
Diagnosis and Repair Workflow Work Flow Work flow OVERALL SEQUENCE Reference 1: On Board Diagnosis Function. Reference 2: DTC Index. Reference 3: Diagnosis Procedure. Reference 4: Component Inspection. Reference 5 ...