Factory-style information for owners and repair work

Nissan Sentra techinfo

Find Nissan Sentra owner information, maintenance instructions, technical references, service procedures and useful repair pages in one clean online library.

Nissan Sentra B18 (2020-2025) Service Manual: C053c Wheel Speed Sensor

Dtc Description

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

C053C

Wheel speed sensor

(Wheel speed sensor generic range/performance)

Diagnosis condition

Engine running

Signal (terminal)

Nissan Sentra Vehicle speed signal

Threshold

Wheel sensor signal is invalid.

Diagnosis delay time

5 seconds

POSSIBLE CAUSE

  • Wheel sensor

  • ABS actuator and control unit (control unit)

FAIL-SAFE

Not applicable

Confirmation Procedure

Confirmation Procedure

  1. CHECK DTC PRIORITY

    If DTC C053C is displayed with other DTC, first perform the confirmation procedure (trouble diagnosis) for other DTC.

    Is applicable DTC detected?

    YES >>

    Perform diagnosis of applicable. Refer to DTC Index.

    NO >>

    GO TO 2.

  2. PRECONDITIONING

    If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

    1. Turn ignition switch OFF and wait at least 10 seconds.

    2. Turn ignition switch ON.

    3. Turn ignition switch OFF and wait at least 10 seconds.

    TESTING CONDITION:

    Before performing the following procedure, confirm that battery voltage is more than 9 V at idle.

    >>

    GO TO 3.

  3. PERFORM DTC CONFIRMATION PROCEDURE

    1. Start the engine and let it idle for at least 5 seconds.

    2. Check DTC.

    Is DTC detected?

    YES >>

    Refer to DTC Diagnosis Procedure.

    NO-1 >>

    To check malfunction symptom before repair: Refer to Intermittent Incident.

    NO-2 >>

    Confirmation after repair: INSPECTION END

Dtc Diagnosis Procedure

DTC Diagnosis Procedure

  1. CHECK DTC PRIORITY

    If DTC C053C is displayed with other DTC, first perform the confirmation procedure (trouble diagnosis) for other DTC.

    Is applicable DTC detected?

    YES >>

    Perform diagnosis of applicable. Refer to DTC Index.

    NO >>

    GO TO 2.

  2. CHECK DTC WITH ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)

    Check DTC with ABS actuator and electric unit (control unit). Refer to DTC Index.

    Is the inspection result normal?

    YES >>

    GO TO 3.

    NO >>

    Perform trouble shooting relevant to DTC indicated.

  3. CHECK WHEEL SENSOR

    Check wheel sensor. Refer to DTC Diagnosis Procedure.

    Is the inspection result normal?

    YES >>

    INSPECTION END

    NO >>

    Repair or replace malfunctioning part.

    U2384 Can Comm Circuit
    Dtc Description DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition U2384 CAN comm err (eVTC) [CAN comm err (eVTC)] ...
    P0010 Intake Valve Timing Control
    Dtc Description DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0010 A camshaft position actuator B1 (“A” c...

    Other materials:

    C106e-01 Steering Angle Sensor
    Dtc Description DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen item (Trouble diagnosis content) DTC detection condition ...

    Evap Canister Purge Volume Control Solenoid Valve
    Removal and Installation Removal and Installation REMOVAL Disconnect harness connector (A) from EVAP canister purge volume control solenoid valve (3). Remove EVAP hose B (1) and EVAP hose C (2) from EVAP canister purge volume control solenoid valve. Remove nut ...

    Removal and Installation
    A/c Switch Assembly Removal and Installation Removal and Installation REMOVAL Remove instrument finisher B. Refer to Removal and Installation. Remove A/C switch assembly screws (A). : Paw ...