Nissan Sentra B18 (2020-2025) Service Manual / Restraints / Srs Air Bag Control System :: Dtc/circuit Diagnosis / Bcm

Nissan Sentra B18 (2020-2025) Service Manual: Bcm

B2c21-23 Front Seat Belt Buckle Switch Lh

Dtc Description

DTC Description

DTC DETECTION LOGIC

DTC No.	CONSULT screen items (Trouble diagnosis content)	DTC Detection Condition
B2C21–23	Seat belt buckle switch LH (Seat belt buckle switch LH)	Diagnosis condition	When ignition switch is ON.
		Signal (terminal)	Front seat belt buckle switch LH signal (BCM connector terminal: 17)
		Threshold	When the ON/OFF change of front seat belt buckle switch LH cannot be detected even once when all the following conditions are satisfied 10 times. Engine running Nissan Sentra Vehicle speed: 3 km/h or more
		Diagnosis delay time	—

POSSIBLE CAUSE

Front seat belt buckle switch LH
Harness or connectors [front seat belt buckle switch LH circuit is open or shorted]

FAIL-SAFE

—

Dtc Confirmation Procedure

DTC Confirmation Procedure

PERFORM DTC CONFIRMATION PROCEDURE
1. CONSULT
  1. Start the engine.
  2. Front seat belt LH is fastened.
  3. Drive Nissan Sentra vehicle at a speed of 3 km/h or more
  4. Ignition switch OFF.
  5. Front seat belt LH is released.
  6. Repeat steps from 1 to 5 (total 10 times).
  7. Select “Self Diagnostic Result” mode of “BCM”.
  8. Check for DTC.
Is DTC detected?
YES >>
Refer to DTC Diagnosis Procedure.
NO >>
To check malfunction symptom before repair: Refer to Intermittent Incident.
NO >>
Confirmation after repair: Inspection End.

Diagnosis Procedure

Diagnosis Procedure

CHECK FRONT SEAT BELT BUCKLE SWITCH LH INPUT SIGNAL

Ignition switch OFF.

Check voltage between front seat belt buckle switch LH harness connector and ground.

(+)		(–)	Condition		Voltage (Approx.)
Front seat belt buckle switch LH
Connector	Terminal
B57	1	Ground	Front seat belt buckle switch LH	OFF (seat belt is released)	Battery voltage
B57	1	Ground	Front seat belt buckle switch LH	ON (seat belt is fastened)	0 V

Is the inspection result normal?

YES >>

GO TO 3.

NO >>

GO TO 2.

CHECK FRONT SEAT BELT BUCKLE SWITCH LH CIRCUIT

Disconnect front seat belt buckle switch LH connector and BCM connector.

Check continuity between front seat belt buckle switch LH harness connector and BCM harness connector.

Front seat belt buckle switch LH		BCM		Continuity
Connector	Terminal	Connector	Terminal	Continuity
B57	1	M84	17	Yes

Check continuity between front seat belt buckle switch LH harness connector and ground.

Front seat belt buckle switch LH		—	Continuity
Connector	Terminal	—	Continuity
B57	1	Ground	No

Is the inspection result normal?

YES >>

Replace BCM. Refer to Removal and Installation.

NO >>

Repair or replace harness.

CHECK FRONT SEAT BELT BUCKLE SWITCH LH GROUND CIRCUIT

Disconnect front seat belt buckle switch LH connector.

Check continuity between front seat belt buckle switch LH harness connector and ground.

Front seat belt buckle switch LH		—	Continuity
Connector	Terminal	—	Continuity
B57	2	Ground	Yes

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace harness.

CHECK FRONT SEAT BELT BUCKLE SWITCH LH
1. Check front seat belt buckle switch LH. Refer to Component Inspection.
Is the inspection result normal?
YES >>
Inspection End.
NO >>
Replace front seat belt buckle switch LH. Refer to Removal and Installation.

B2f60-55 Front Seat Belt Buckle Switch Lh

Dtc Description

DTC Description

DTC DETECTION LOGIC

DTC No.	CONSULT screen items (Trouble diagnosis content)	DTC detecting condition
B2F60-55	Seat belt buckle switch LH (Seat belt buckle switch LH)	Diagnosis condition	When ignition switch is ON.
		Signal (terminal)	—
		Threshold	Configuration of the BCM is not completed
		Diagnosis delay time	1 second or less

POSSIBLE CAUSE

BCM is not configured

FAIL-SAFE

—

Dtc Confirmation Procedure

DTC Confirmation Procedure

PERFORM DTC CONFIRMATION PROCEDURE
1. CONSULT
  1. Ignition switch ON.
  2. Select “Self Diagnostic Result” mode of “BCM”.
  3. Check for DTC.
Is DTC detected?
YES>>
Refer to DTC Diagnosis Procedure.
NO>>
To check malfunction symptom before repair: Refer to Intermittent Incident.
NO>>
Confirmation after repair: Inspection End.

Diagnosis Procedure

Diagnosis Procedure

BCM CONFIGURATION
1. Perform configuration. Refer to Work Procedure.
Is the DTC detected?
YES >>
GO TO 2.
NO >>
Inspection End.
REPLACE BCM
1. Replace BCM. Refer to Removal and Installation.
>>
Inspection End.

 U0073-00 Can Comm Circuit

Dtc Description DTC Description CAN (Controller Area Network) is a serial communication line for real time applications. It is an on-Nissan Sentra vehicle multiplex communicatio...

 Srs Air Bag Control System. Symptom Diagnosis

Srs Air Bag Warning Lamp Does Not Turn Off. Diagnosis Procedure Diagnosis Procedure Diagnosis Procedure CHECK AIR BAG MODULE AND SEAT BELT PRE-TENSIONER Check the deployment of ...

Other materials:

Radiator
Exploded View Exploded View 1. Reservoir tank cap 2. Reservoir tank 3. ...

Oil Filter
Removal and Installation Removal and Installation REMOVAL Remove the front under cover. Refer to Removal and Installation. Using suitable tool (A), remove the oil filter (1). CAUTION: Oil filter is provided with relief valve. Be ...

Vehicle identification
Vehicle Identification Number (VIN) plate The Vehicle Identification Number (VIN) plate on your Nissan Sentra is attached in the location shown. This unique VIN serves as the primary identification number for the vehicle and is used for vehicle registration, insurance, warranty tracking, ...