Nissan Sentra manuals

Nissan Sentra B18 (2020-2025) Service Manual: B1339 Rear Camera Connection

Nissan Sentra B18 (2020-2025) Service Manual / Driver Information & Multimedia / Audio, Visual & Navigation System :: Display Audio Without Bose with 8" Color Display / Dtc/circuit Diagnosis / B1339 Rear Camera Connection

Dtc Description

DTC Description

DTC DETECTION LOGIC

DTC No.

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

B1339-8F

Rear camera connection

(Rear view camera connection)

[–]

Diagnosis condition

When ignition switch is ON.

Signal (terminal)

Camera image signal circuit (terminal 52)

Threshold

–

Diagnosis delay time

30 seconds or more

POSSIBLE CAUSE

FAIL-SAFE

Rear view camera is inoperative.

Confirmation Procedure

Confirmation Procedure

  1. PERFORM DTC CONFIRMATION PROCEDURE

    1. CONSULT

      1. Ignition switch ON.

      2. Ignition switch OFF and wait at least 30 seconds.

      3. Ignition switch ON and wait at least 30 seconds or more.

      4. Select “Self Diagnostic Result” mode of “MULTI AV”.

      5. Check DTC.

    Is DTC B1339–8F detected?

    YES>>

    Refer to DTC Diagnosis Procedure.

    NO>>

    To check malfunction symptom before repair: Refer to Intermittent Incident.

    NO>>

    Confirmation after repair: Inspection End.

Dtc Diagnosis Procedure

DTC Diagnosis Procedure

  1. CHECK CAMERA IMAGE SIGNAL CIRCUIT FOR OPEN

      1. Ignition switch OFF.

      2. Disconnect AV control unit connector and rear view camera connector.

      3. Check the continuity between AV control unit connector and rear view camera connector.

        AV control unit

        Rear view camera

        Continuity

        Connector

        Terminal

        Connector

        Terminal

        M104

        52

        B30

        3

        Yes

    Is the inspection result normal?

    YES >>

    GO TO 2.

    NO >>

    Repair harness or connector.

  2. CHECK CAMERA IMAGE SIGNAL CIRCUIT FOR SHORT

    1. Check the continuity between AV control unit connector and ground.

      AV control unit

      −

      Continuity

      Connector

      Terminal

      M104

      52

      Ground

      No

    Is the inspection result normal?

    YES >>

    GO TO 3.

    NO >>

    Repair harness or connector.

  3. CHECK CAMERA IMAGE SIGNAL

      1. Connect AV control unit connector and rear view camera connector.

      2. Ignition switch ON.

      3. Shift the selector lever to “R” position

      4. Check the signal between AV control unit connector and ground.

        AV control unit

        (-)

        Condition

        Reference value

        (+)

        Connector

        Terminal

        M104

        52

        Ground

        Camera image is displayed

    Is the inspection result normal?

    YES >>

    Replace AV control unit. Refer to Removal and Installation.

    NO >>

    Replace rear view camera. Refer to Removal and Installation.

B1341 Head Unit
Dtc Description DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms ...

Other materials:

U2156-87 Can Comm Circuit
Dtc Description DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen item (Trouble diagnosis content) DTC detection condition ...

System
Meter System System Description System Description SYSTEM DIAGRAM Combination Meter Input Signal (CAN Communication Signal) Transmit unit Signal name ...

Front disc brake
Exploded View Cap Bleeder valve Cylinder body Piston seal Piston Piston boot Upper sliding pin Lower sliding pin Sliding pin boot Bushing Torque member Apply brake fluid Apply rubber grease Disassembly and Assembly DISASSEMBLY Place a wooden block as shown, and ...

© 2014-2026 Copyright www.nisentra.com