Nissan Sentra B18 (2020-2025) Service Manual: B1328 External Microphone 1
Dtc Description
DTC Description
DTC DETECTION LOGIC
|
DTC No. |
CONSULT screen terms (Trouble diagnosis content) |
DTC detection condition |
||
|---|---|---|---|---|
|
B1328–13 |
External Microphone 1 (Microphone) |
[OPEN] |
Diagnosis condition |
When ignition switch is ON. |
|
Signal (terminal) |
— |
|||
|
Threshold |
– |
|||
|
Diagnosis delay time |
30 seconds or more |
|||
|
B1328–11 |
[GND–SHORT] |
Diagnosis condition |
When ignition switch is ON. |
|
|
Signal (terminal) |
— |
|||
|
Threshold |
– |
|||
|
Diagnosis delay time |
30 seconds or more |
|||
|
B1328–12 |
[VB–SHOR] |
Diagnosis condition |
When ignition switch is ON. |
|
|
Signal (terminal) |
— |
|||
|
Threshold |
– |
|||
|
Diagnosis delay time |
30 seconds or more |
|||
POSSIBLE CAUSE
-
Microphone is not connected
-
Harness or connector
-
Microphone
FAIL-SAFE
Microphone is inoperative
Dtc Confirmation Procedure
DTC Confirmation Procedure
-
PERFORM DTC CONFIRMATION PROCEDURE
-
CONSULT-
Ignition switch ON.
-
Ignition switch OFF and wait at least 30 seconds.
-
Ignition switch ON and wait at least 30 seconds or more.
-
Select “Self Diagnostic Result” mode of “MULTI AV”.
-
Check DTC.
-
Is DTC B1328 detected?
YES>>Proceed to DTC Diagnosis Procedure.
NO>>To check malfunction symptom before repair: Refer to Intermittent Incident.
NO>>Confirmation after repair: Inspection End.
-
Diagnosis Procedure
Diagnosis Procedure
-
DETERMINE MALFUNCTION TYPE
-
CONSULT-
Ignition switch ON.
-
Ignition switch OFF and wait at least 30 seconds.
-
Ignition switch ON and wait at least 30 seconds or more.
-
Select “Self Diagnostic Result” mode of “MULTI AV”.
-
Check DTC.
-
Is DTC B1328–11, 12 or 13 detected?
YES>>13 [OPEN], or 11 [GND-SHORT] – GO TO 2.
YES>>12 [VB–SHOR] – GO TO 3.
NO>>Refer to Intermittent Incident.
-
-
CHECK MICROPHONE CIRCUITS FOR OPEN OR SHORT TO GROUND
-
-
Ignition switch OFF.
-
Disconnect AV control unit connector and microphone connector.
-
Check the continuity between AV control unit connector and microphone connector.
AV control unit
Microphone
Continuity
Connector
Terminal
Connector
Terminal
M104
21
R17
1
Yes
22
4
42
2
50
5
-
Check the continuity between AV control unit connector and ground.
AV control unit
—
Continuity
Connector
Terminal
M104
21
Ground
Yes
22
50
-
Is the inspection result normal?
YES >>Replace microphone. Refer to Removal and Installation.
NO >>Repair or replace harness or connectors.
-
-
CHECK MICROPHONE CIRCUITS FOR SHORT TO POWER SUPPLY
-
-
Ignition switch OFF.
-
Disconnect AV control unit connector and microphone connector.
-
Ignition switch ON.
-
Check the voltage between AV control unit connector and ground.
AV control unit
(−)
Voltage
(Approx.)
(+)
Connector
Terminal
M104
21
Ground
0 V
22
42
50
-
Is the inspection result normal?
YES >>Replace microphone. Refer to Removal and Installation.
NO >>Repair or replace harness or connectors.
-
Other materials:
B2f73-23 Clutch Switch
Dtc Description
DTC Description
DTC DETECTION LOGIC
DTC No.
CONSULT screen items
(Trouble diagnosis
content)
DTC detecting condition
...
Mode Door Motor
Diagnosis Procedure
Diagnosis Procedure
CHECK MODE DOOR MOTOR POWER SUPPLY
Ignition switch ON.
Check voltage between mode door motor harness connector
and ground.
...
P0171 Fuel Injection System Function
Dtc Description
DTC Description
With the Air/Fuel Mixture Ratio Self-Learning Control, the actual
mixture ratio can be brought closely to the theoretical mixture ratio based on
the mixture ratio feedback signal from A/F sensor 1. The ECM calculatesthe
necessary compensation to corre ...