Nissan Sentra manuals

Toyota Camry Owner's Manual (2023): Automatic door locking and unlocking systems

The following functions can be set or cancelled:

Opening, closing and locking the doors

■Switching the door unlock function (vehicles with a smart key system)

It is possible to set which doors the entry function unlocks using the wireless remote control.

1. Turn the engine switch off.

2. When the indicator light on the key surface is not on, press and hold , or for approximately 5 seconds while pressing and holding .

The setting changes each time an operation is performed, as shown below.

(When changing the setting continuously, release the buttons, wait for at least 5 seconds, and repeat step 2.)

Opening, closing and locking the doors

*1: 4.2-inch display
*2: 7-inch display

To prevent unintended triggering of the alarm, unlock the doors using the wireless remote control and open and close a door once after the settings have been changed. (If a door is not opened within 60 seconds after is pressed, the doors will be locked again and the alarm will automatically be set.) In case that the alarm is triggered, immediately stop the alarm.

■Impact detection door lock release system

In the event that the vehicle is subject to a strong impact, all the doors are unlocked. Depending on the force of the impact or the type of accident, however, the system may not operate.

■Open door warning buzzer

If the vehicle reaches a speed of 3 mph (5 km/h), the master warning light flashes and a buzzer sounds to indicate that the door(s) are not yet fully closed.

The open door(s) is displayed on the multi-information display.

■Conditions affecting the operation of the smart key system or wireless remote control

Vehicles without a smart key system

Vehicles with a smart key system

■Rear seat reminder function

In order to remind you not to forget luggage, etc. in the rear seat, when the engine switch is turned off after any of the following conditions are met, a buzzer will sound and a message will be displayed on the multi-information display for approximately 6 seconds.

However, if a rear door is opened and then closed within approximately 2 seconds, the rear seat reminder function may not operate.

The rear seat reminder function determines that luggage, etc. has been placed in a rear seat based on opening and closing of a rear door. Therefore, depending on the situation, the rear seat reminder function may not operate and you may still forget luggage, etc. in the rear seat, or it may operate unnecessarily.

The rear seat reminder function can be enabled/disabled.

■Customization

Some functions can be customized.

WARNING

■To prevent an accident

Observe the following precautions while driving the vehicle.

Failure to do so may result in a door opening and an occupant falling out, resulting in death or serious injury.

■When opening or closing a door

Check the surroundings of the vehicle such as whether the vehicle is on an incline, whether there is enough space for a door to open and whether a strong wind is blowing.

When opening or closing the door, hold the door handle tightly to prepare for any unpredictable movement.

Doors
Unlocking and locking the doors from the outside ◆ Smart key system (if equipped) Carry the electronic key to enable this function. Grip the driver's door handle to unlock the door. Holding ...

Trunk
The trunk can be opened using the trunk opener switch, entry function (vehicles with a smart key system), wireless remote control or key. Opening the trunk from inside the vehicle Press and hold t ...

Other materials:

Symptom diagnosis
Door does not lock/unlock with door lock and unlock switch All door ALL DOOR : Description All doors do not lock/unlock using door lock and unlock switch. ALL DOOR : Diagnosis Procedure 1.CHECK DOOR LOCK AND UNLOCK SWITCH Check door lock and unlock switch. Refer to DLK-97, "Component F ...

Front disc brake
Exploded View Cap Bleeder valve Cylinder body Piston seal Piston Piston boot Upper sliding pin Lower sliding pin Sliding pin boot Bushing Torque member Apply brake fluid Apply rubber grease Disassembly and Assembly DISASSEMBLY Place a wooden block as shown, and ...

P1651 Starter motor relay
Description ECM controls ON/OFF state of the starter relay, according to the engine and vehicle condition. ECM transmits a control signal to IPDM E/R by CAN communication. Under normal conditions, ECM controls and maintains the starter relay in OFF state during following condition: Engi ...

© 2014-2023 Copyright www.nisentra.com