Nissan Sentra Owners Manual: Text messaging

Nissan Sentra Owners Manual / Monitor, climate, audio, phone and voice recognition systems / Bluetooth® Hands-Free Phone System without Navigation System (Type B) (if so equipped) / Text messaging

WARNING

Laws in some jurisdictions may restrict the use of some of the applications and features, such as social networking and texting.
Laws in some jurisdictions may restrict the use of “Text-to-Speech”. Check local regulations before using this feature.
Use the text messaging feature after stopping your vehicle in a safe location.

If you have to use the feature while driving, exercise extreme caution at all times so full attention may be given to vehicle operation.
If you are unable to devote full attention to vehicle operation while using the text messaging feature, pull off the road to a safe location and stop your vehicle.

NOTE:

This feature is automatically disabled if the connected device does not support the Message Access Profile (MAP). See the phone’s Owner’s Manual for details and instructions.

The system allows for the sending and receiving of text messages through the vehicle interface.

Sending a text message:

Press the button.

Say “Send Text”.
The system will provide a list of available commands in order to determine the recipient of the text message. Choose from the following:

(a name)
Number
Incoming Calls
Outgoing Calls
Missed Calls

For more information about these options, see “Voice commands” in this section.

Once a recipient is chosen, the system prompts for which message to send. Five predefined messages are available as well as three custom messages. To choose one of the predefined messages, speak one of the following:

“Driving, can’t text”
“Call me”
“On my way”
“Running late”
“Okay”

To send one of the custom messages, say “Custom Message”. If more than one custom message is stored, the system will prompt for the number of the desired custom message. For more information on setting and managing custom text messages, see “Bluetooth® settings” in this section.

Reading a received text message:

Press the button.

Say “Read Text”.

The text message, sender and delivery time are shown on the screen. Use the tuning switch on the steering wheel to scroll through all text messages if more than one are available. Press the screen. button to exit the text message
screen.

Press the button to access the
following options for replying to the text message:

Call Back

Speak this command to call the sender of the text message using the Bluetooth® Hands-Free Phone System.

Send Text

Speak this command to send a text message response to the sender of the text message.

Read Text

Speak this command to read the text message again.

Previous Text

Speak this command to move to the previous text message (if available).

Next Text

Speak this command to move to the next text message (if available).

NOTE:

Text messages are only displayed if the vehicle speed is less than 5 mph (8 km/h).

During a call

While a call is active, press the button to access additional options. Speak one of the following commands: “(numbers)” – Speak numbers and then say “Send” or say “Correction” ...

Bluetooth® settings

To access and adjust the settings for the Bluetooth® Hands-Free Phone System: Press the SETTING button. Use the TUNE/SCROLL knob to select “Bluetooth” and then press the ENTER button ...

Other materials:

P1574 ASCD Vehicle speed sensor
Description The ECM receives two vehicle speed sensor signals via CAN communication line. One is sent from combination meter, and the other is from TCM (Transmission control module). The ECM uses these signals for ASCD control. Refer to EC-51, "AUTOMATIC SPEED CONTROL DEVICE (ASCD) : Sys ...

Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER"
The Supplemental Restraint System such as вЂњAIR BAGвЂќ and вЂњSEAT BELT PRE-TENSIONERвЂќ, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision. Information necessary to service the system ...

Can communication circuit
Diagnosis procedure 1.Connector inspection Turn the ignition switch off. Disconnect the battery cable from the negative terminal. Disconnect all the unit connectors on CAN communication system. Check terminals and connectors for damage, bend and loose connection. Is the inspection resu ...