Nissan Sentra Service Manual: Rear rh side power window does not operate
When both power window main switch and rear power window switch RH are operated
When both power window main switch and rear power window switch rh are operated : diagnosis procedure
1.CHECK REAR POWER WINDOW SWITCH RH
Check rear power window switch RH.
Refer to PWC-40, "REAR POWER WINDOW SWITCH : Diagnosis Procedure".
Is the inspection result normal? YES >> GO TO 2.
NO >> Repair or replace the malfunctioning parts.
2.CHECK REAR POWER WINDOW MOTOR RH
Check rear power window motor RH.
Refer to PWC-48, "REAR RH : Diagnosis Procedure".
Is the inspection result normal? YES >> GO TO 3.
NO >> Repair or replace the malfunctioning parts.
3.REPLACE POWER WINDOW MAIN SWITCH
- Replace power window main switch.
- Confirm the operation after replacement.
Is the result normal? YES >> INSPECTION END
NO >> Check intermittent incident. Refer to GI-39, "Intermittent Incident".
When rear power window switch rh is operated
When rear power window switch rh is operated : diagnosis procedure
1.CHECK REAR POWER WINDOW SWITCH RH POWER SUPPLY AND GROUND CIRCUIT
Check rear power window switch RH power supply and ground circuit.
Refer to PWC-40, "REAR POWER WINDOW SWITCH : Diagnosis Procedure".
Is the inspection result normal? YES >> GO TO 2.
NO >> Repair or replace the malfunctioning parts.
2.CHECK REAR POWER WINDOW SWITCH RH
Check rear power window switch RH.
Refer to PWC-40, "REAR POWER WINDOW SWITCH : Diagnosis Procedure".
Is the inspection result normal? YES >> GO TO 3.
NO >> Repair or replace the malfunctioning parts.
3.REPLACE POWER WINDOW MAIN SWITCH
- Replace power window main switch.
- Confirm the operation after replacement.
Is the result normal? YES >> INSPECTION END
NO >> Check intermittent incident. Refer to GI-39, "Intermittent Incident".
When power window main switch is operated
When power window main switch is operated : diagnosis procedure
1.CHECK REAR POWER WINDOW SWITCH RH
Check rear power window switch RH.
Refer to PWC-40, "REAR POWER WINDOW SWITCH : Diagnosis Procedure".
Is the inspection result normal? YES >> GO TO 2.
NO >> Repair or replace the malfunctioning parts.
2.REPLACE POWER WINDOW MAIN SWITCH
- Replace power window main switch.
- Confirm the operation after replacement.
Is the result normal? YES >> INSPECTION END
NO >> Check intermittent incident. Refer to GI-39, "Intermittent Incident".
Rear lh side power window does not operate
When both power window main switch and rear power window switch lh are
operated
When both power window main switch and rear power window switch lh are
operated : diagnosis procedure
1.CHECK REAR ...
Auto operation does not operate but manual operate normally (driver side)
Diagnosis Procedure
1.PERFORM INITIALIZATION PROCEDURE
Initialization procedure is executed and operation is confirmed.
Refer to PWC-29, "Work Procedure".
Is the inspection result no ...
Other materials:
Ecu diagnosis information
BCM
Reference value
Note:
The signal tech ii tool (j-50190) can be used to perform the following
functions. Refer to the signal tech ii
user guide for additional information.
Activate and display tpms transmitter ids
Display tire pressure reported by the tpms transmitter
Read TPMS DTCs ...
Glove box lamp
Removal and installation
Warning:
Do not touch bulb while it is lit or right after being turned off.
Burning may result.
Caution:
Do not touch glass surface of the bulb with bare hands or allow oil or
grease to get on it to prevent
damage to bulb.
Removal
Remove the glove box assembly ...
P1148 Closed loop control
DTC Logic
DTC DETECTION LOGIC
NOTE:
DTC P1148 is displayed with DTC for A/F sensor 1.
When the DTC is detected, perform the trouble diagnosis of DTC corresponding to
A/F sensor 1.
DTC No.
CONSULT screen terms
(Trouble diagnosis content)
DTC detecting condition
Possible ca ...