Nissan Sentra Owners Manual: Using the system

Nissan Sentra Owners Manual / Monitor, climate, audio, phone and voice recognition systems / Bluetooth® Hands-Free Phone System without Navigation System (Type B) (if so equipped) / Using the system

The NISSAN Voice Recognition system allows hands-free operation of the Bluetooth® Phone System.

If the vehicle is in motion, some commands may not be available so full attention may be given to vehicle operation.

Initialization

When the ignition switch is placed in the ON position, NISSAN Voice Recognition is initialized, which takes a few seconds. If the
button is pressed before the initialization completes, the system will announce “Hands-free phone system not ready” and will not react to voice commands.

Operating tips

To get the best performance out of the NISSAN Voice Recognition system, observe the following:

Keep the interior of the vehicle as quiet as possible. Close the windows to eliminate surrounding noises (traffic noises, vibration sounds, etc.), which may prevent the system from recognizing voice commands correctly.
Wait until the tone sounds before speaking a command. Otherwise, the command will not be received properly.
Start speaking a command within 5 seconds after the tone sounds.
Speak in a natural voice without pausing between words.

Giving voice commands

To operate NISSAN Voice Recognition, press and release the button
located on the steering wheel. After the tone sounds, speak a command.

The command given is picked up by the microphone, and voice feedback is given when the command is accepted.

If you need to hear the available commands for the current menu again, say “Help” and the system will repeat them.
If a command is not recognized, the system announces, “Command not recognized.

Please try again.”Make sure the command is said exactly as prompted by the system and repeat the command in a clear voice.
If you want to go back to the previous command, you can say “Go back” or “Correction” any time the system is waiting for a response.
You can cancel a command when the system is waiting for a response by saying, “Cancel” or “Quit.” The system announces “Cancel” and ends the VR session. You can also press and hold the button
on the steering wheel for 5 seconds at any time to end the VR session. Whenever the VR session is cancelled, a double beep is played to indicate you have exited the system.
If you want to adjust the volume of the voice feedback, press the volume control switches (+ or -) on the steering wheel while being provided with feedback. You can also use the radio volume control knob.

Voice Prompt Interrupt

In most cases you can interrupt the voice feedback to speak the next command by pressing the After button on the steering wheel.
After interrupting the system, wait for a beep before speaking your command.

One Shot Call

To use the system faster, you may speak the second level commands with the main menu command on the main menu. For example, press the button and after the tone
say, “Call Redial”.

Regulatory Information

FCC Regulatory information CAUTION: To maintain compliance with FCC’s RF exposure guidelines, use only the supplied antenna. Unauthorized antenna, modification, or attachments could damage ...

Control buttons

The control buttons for the Bluetooth® Hands- Free Phone System are located on the steering wheel. PHONE/SEND Press the button to initiate a VR session or answer an incoming call. You ca ...

Other materials:

L terminal circuit (short)
Description The terminal вЂњlвЂќ circuit controls the charge warning lamp. The charge warning lamp turns on when the ignition switch is set to on or start. When the generator is providing sufficient voltage with the engine running, the charge warning lamp turns off. If the charge warni ...

Front wiper auto stop signal circuit
Component function check 1. Check front wiper (auto stop) operation Consult data monitor Select вЂњWIP AUTO STOPвЂќ of IPDM E/R DATA MONITOR item. Operate the front wiper. With the front wiper operation, check the monitor status. Is the inspection result normal? YES >> ...

Both side headlamps do not switch to high beam
Description The headlamps (both sides) do not switch to high beam when the lighting switch is in the hi or pass setting. Diagnosis procedure 1.Combination switch (lighting and turn signal switch) inspection Check the combination switch (lighting and turn signal switch). Refer to bcs-72, &q ...