Nissan Sentra B18 (2020-2025) Service Manual / Engine / Work Procedure (After Replacing Electric Throttle Control Actuator) / Dtc/circuit Diagnosis / U012e Can Communication

Nissan Sentra B18 (2020-2025) Service Manual: U012e Can Communication

Dtc Description

DTC Description

DTC DETECTION LOGIC

DTC	CONSULT screen terms (Trouble diagnosis content)	DTC detection condition
U012E	Communication error (lost) (Lost communication with camshaft position control module)	Diagnosis condition	Engine running at idle
		Signal (terminal)	CAN communication signal
		Threshold	Internal error of the electric intake valve timing control module is detected.
		Diagnosis delay time	—

POSSIBLE CAUSE

Electric Intake valve timing control module
ECM

FAIL-SAFE

Engine Control System

Engine operating condition in fail-safe mode
Fail safe mode		Nissan Sentra Vehicle behavior
Device fix mode		This mode fixes the electric IVT motor and the EVT control solenoid valve in the reference position. The intake manifold runner control valve motor is turned OFF (intake manifold runner control valve opens).
Combustion control mode	Stratified charge combustion control at starting	No stratified charge combustion at starting (cold start).
	Idle speed control	Stops feedback control of idle speed and controls with specified speed.
	Recovery speed control at decelerating	Stops recovery speed control by the fuel cut at decelerating and controls with specified speed.
	Idle neutral control	Stops idle neutral control.
Others		ECM stops the electric valve timing control. (The camshaft returns to the position of most retard angle.)

Idle Start/Stop System

When a DTC is detected, the start/stop indicator lamp blinks slowly and the idle start/stop system operation is prohibited.

When ECM detects error while operating the idle start/stop system, ECM restarts the engine.

Confirmation Procedure

Confirmation Procedure

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted. always perform the following procedure before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
>>
GO TO 2.
PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine and let it idle for at least 5 seconds.
2. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >>
Refer to DTC Diagnosis Procedure.
NO-1 >>
To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2 >>
Confirmation after repair: INSPECTION END

Dtc Diagnosis Procedure

DTC Diagnosis Procedure

CHECK CAN COMMUNICATION LINE

Perform trouble diagnosis of CAN communication system. Refer to Trouble Diagnosis Flow Chart.

Is the inspection result normal?
YES >>
GO TO 2.
NO >>
Repair or replace error-detected parts.
CHECK INTERMITTENT INCIDENT

Check intermittent incident. Refer to Trouble Diagnosis Flow Chart.

Is the inspection result normal?
YES >>
GO TO 3.
NO >>
Repair or replace error-detected parts.
REPLACE ELECTRIC INTAKE VALVE TIMING CONTROL MODULE
1. Replace electric intake valve timing control module. Refer to Removal & Installation.
2. Perform DTC confirmation procedure. Refer to Confirmation Procedure.
Is DTC U012E detected again?
YES >>
Replace ECM. Refer to Removal & Installation.
NO >>
INSPECTION END

 U0101 Can Comm Circuit

Dtc Description DTC Description CAN (Controller Area Network) is a serial communication line for real time application. It is an on-Nissan Sentra vehicle multiplex communication...

 U0131 Can Communication

Dtc Description DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition U0131 Lost communication (EPS C/U) (Lost Communi...

Other materials:

P2808-00 Pressure Control Solenoid G
Dtc Description DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection conditi ...

B2223-16 Combination Meter
Dtc Description DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detected condition ...

Symptom Diagnosis
The Fuel Gauge Indicator Does Not Operate Description Description Fuel gauge will not indicate from a certain position. Diagnosis Procedure Diagnosis Procedure PERFORM COMBINATION METER SELF-DIAGNOSIS MODE Perform the self-diagnosis mode ...