Nissan Sentra Service Manual: Side window glass
Components

- Side window glass
- Spacer
- Headlining
- Rear body pillar
- Rear pillar finisher
- Rear door weatherstrip
- Primer area
- Adhesive
- 7 mm (0.3 in)
- 12 mm (0.5 in)
Removal and Installation
REMOVAL
- Remove the rear pillar finisher. Refer to INT-29, "REAR PILLAR FINISHER
: Removal and Installation".
- After removing moldings, remove the glass using piano wire or power
cutting tool (A) and an inflatable
pump (B).

- Apply protective tape around the windshield glass to protect the painted
surface from damage.
- If the windshield glass is to be reused, mark the body and the glass
with matching marks.
- Minimum adhesive coating amount 8 +3,-0 g/100 mm (0.28 +0.11,-0 oz/3.9
in) all around.
- Minimum primer application area 20.0 mm (0.79 in) on body and glass
side.
WARNING:
When cutting the glass from the vehicle, always wear safety glasses
and heavy gloves to help prevent
glass splinters from entering your eyes or cutting your hands.
CAUTION:
- Be careful not to scratch the glass when removing.
- Do not set or stand the glass on its edge. Small chips may develop
into cracks.
- Apply protective tape around the windshield glass to protect the
painted surface from damage.
INSTALLATION
Installation is in the reverse order of removal.
- If repainting near the rear window glass flange area, protect the flange
adhesion area by masking the flange.
- Use a genuine NISSAN Urethane Adhesive Kit (if available) or equivalent
and follow the instructions furnished
with it.
- Adhesive shall be continuously applied to assure watertightness. Glass
installation shall be finished within
five minutes after applying the adhesive.
- The start and finish of the urethane adhesive application should be
located at the bottom to assure watertightness.
- While the urethane adhesive is curing, open a door window. This will
prevent the glass from being forced out
by passenger compartment air pressure when a door is closed.
- Inform the customer that the vehicle should remain stationary until the
urethane adhesive has completely
cured (preferably 24 hours). Curing time varies with temperature and
humidity.
WARNING:
CAUTION:
- Do not use an adhesive which is past its usable term. Shelf life
of this product is limited to six
months after the date of manufacture. Carefully adhere to the expiration or
manufacture date printed
on the box or product.
- Keep primers and adhesive in a cool, dry place. Ideally, they
should be stored in a refrigerator.
- Do not leave primers or adhesive cartridge unattended with their
caps open or off.
- The vehicle should not be driven for at least 24 hours or until
the urethane adhesive has completely
cured. Curing time varies depending on temperature and humidity. The curing
time will increase
under lower temperature and lower humidity.
REPAIRING WATER LEAKS FOR SIDE WINDOW GLASS
- Leaks can be repaired without removing and reinstalling glass.
- If water is leaking between the urethane adhesive material and body or
glass, determine the extent of leakage.
- This can be done by applying water to the side window area while pushing
glass outward.
- To stop the leak, apply primer (if necessary) and then urethane adhesive
to the leak point.
Removal and Installation
REMOVAL
Remove the rear door glass regulator (1). Refer to GW-21,
"Removal and Installation"
Remove the screws and the rear power window motor (2).
I ...
Exploded View
Rear window glass
Spacer
Rubber dam
Body side outer
Headlining
Roof panel
Trunk lid
Adhesive
12 mm (0.5 in)
7 mm (0.3 in)
2.0 mm (0.08 in)
3 mm (0.1 in) ...
Other materials:
Speedometer and odometer
Speedometer
The speedometer indicates the vehicle speed.
Odometer/Twin trip odometer
The odometer 2 and the twin trip odometer 1
are displayed when the ignition switch is placed
in the ON position.
The odometer records the total distance the vehicle
has been driven.
The twin trip o ...
Symptom diagnosis
CVT CONTROL SYSTEM
Symptom Table
The diagnosis item number indicates the order of check. Start checking in the
order from 1.
...
6M/T
6M/T : Exploded View (LH)
Circular clip
Dust shield
Slide joint housing
Snap ring
Spider assembly
Boot band
Boot
Shaft
Damper band
Dynamic damper
Circular clip
Joint sub-assembly
Wheel side
6M/T : Disassembly and Assembly (LH)
DISASSEMBLY (WHEEL SIDE)
CAUTION:
...
В© 2014-2023 Copyright www.nisentra.com