Removal and Installation (LH)

When removing components such as hoses, tubes, lines, etc., cap or plug openings to prevent fluid from spilling.

REMOVAL

For M/T models, drain the M/T oil. Refer to Draining.

Remove disc brake rotor. Refer to Removal and Installation.

CAUTION:

Do not depress the brake pedal while the brake caliper is removed.

Remove the wheel sensor bolt. Position the wheel sensor and the wheel sensor harness aside. Refer to Removal and Installation.

CAUTION:

Do not pull or twist the harness when removing.

Using hammer (A) and Tool (B) release staked area (C) of wheel hub lock nut (D).

Visually verify that staked area (A) of wheel hub lock nut (B) is completely released from front drive shaft (1) or damage to drive shaft can occur.

Warning:

To avoid risk of death or severe personal injury:

Hold the wheel hub and bearing using Tool (A). Loosen the wheel hub lock nut.

Warning:

To avoid risk of death or severe personal injury:

Using a piece of wood and a suitable tool, tap on the wheel hub lock nut to disengage the drive shaft from the wheel hub and bearing.

CAUTION:

• Do not place the drive shaft joint at an extreme angle. Also be careful not to overextend slide joint.

• Do not allow the drive shaft to hang down without support.

Use a suitable puller if the drive shaft cannot be separated from the wheel hub and bearing even after performing the above procedure.

Remove the wheel hub lock nut.

Remove the nut and bolt from the lower ball joint. Disconnect the steering knuckle from the transverse link.

Remove the drive shaft from the wheel hub and bearing.

Insert the Tool (A) between the shaft and the transaxle. Remove the drive shaft from the transaxle.

CAUTION:

Confirm that the circular clip is attached to the drive shaft.

Remove the differential side oil seal. Refer to Removal and Installation (6MT: RS6F94R), Removal and Installation (CVT: RE0F10D).

Inspect the components. Refer to Inspection (LH).

INSTALLATION

Installation is in the reverse order of removal.

TRANSAXLE SIDE

• Install a new differential side oil seal. Refer to Removal and Installation (6MT: RS6F94R), Removal and Installation (CVT: RE0F10D).

  CAUTION:

  Do not reuse the differential side oil seal.

• Place Tool (A) onto the differential side oil seal to prevent damage to the oil seal while inserting the drive shaft. Slide drive shaft sliding joint and tap with a hammer to install securely.

  

  Tool (A) number

  : KV38107900 ( — )

  Warning:

  Ensure that the circular clip is properly engaged, otherwise the joint sub-assembly could pull away from the transaxle during Nissan Sentra vehicle operation resulting in loss of drive force and possible drive shaft damage, which may cause a crash and serious injury or damage to the drive shaft.

  • To ensure the circular clip is properly engaged, grasp the housing (1) and pull back and forth in axial direction while listening for clicking sounds.

    

  • Pull the joint sub-assembly in the axial direction away from transaxle. Confirm that the joint sub assembly cannot be pulled out.

• For M/T models, refill the M/T oil. Refer to Refilling.

• For CVT models, check the CVT fluid level. Check the CVT for leaks. Refer to Inspection (CVT: RE0F10D).

• Complete the inspection. Refer to Inspection (LH).

WHEEL HUB SIDE

• Clean the mating surfaces of the wheel hub lock nut and the wheel hub and bearing.

  Warning:

  To avoid risk of death or severe personal injury:

  • Do not apply lubricating oil to these mating surfaces.

  • Check that there is no clearance between wheel stud and wheel hub and bearing.

  • Do not use a power tool to tighten the wheel hub lock nut.

  • Align the marks made on the rotor and the front wheel hub during disassembly.

  • Do not reuse lower strut nut.

  • Do not reuse the wheel hub lock nut.

  • Clean mating surfaces of wheel hub lock nut and wheel hub and bearing.

  • Do not apply lubricating oil to these matching surface.

• Apply a moderate coat of paste [service parts (440037S000)] to bearing surface (A) as shown.

  Note:

  Always check with the Parts Department for the latest parts information.

• Hold the wheel hub and bearing using suitable tool. Tighten the wheel hub lock nut.

  Wheel hub lock nut

  165 N·m (17 kg−m, 122 ft−lb)

  CAUTION:

  • Do not reuse the wheel hub lock nut.

  • Since the drive shaft is assembled by press-fitting, use a torque wrench to tighten the wheel hub lock nut. Do not use a power tool.

  • Too much torque causes axle noise. Too little torque causes wheel bearing looseness. Tighten the wheel hub lock nut to the specification.

  Tool number

  : KV4014000 ( — )

• Using hammer (A) and cold chisel (B) stake the wheel hub lock nut (C) as shown.

  

  Warning:

  To avoid the risk of death or severe personal injury:

  • Use the following range when staking the wheel hub lock nut.

    

  (A)	: 6.2 mm (0.244 in)
  (B)	: 26.4 - 27.8 mm (1.039 - 1.094 in)

• Align the matching marks (A) on the disc brake rotor and on the wheel hub and bearing.

  

• Complete the inspection. Refer to Inspection (LH).