S Nissan Sentra Manuals Library
Factory-style information for owners and repair work

Nissan Sentra techinfo

Find Nissan Sentra owner information, maintenance instructions, technical references, service procedures and useful repair pages in one clean online library.

Quick access Sentra Docs
B18 Owner's 2020-2025 Sentra owner information B18 Service 2020-2025 Sentra Workshop manual B17 Owner's 2013-2019 Sentra owner documentation B17 Service 2013-2019 Sentra service information

Nissan Sentra B18 (2020-2025) Service Manual: P2297 Air Fuel Ratio Sensor 1

Dtc Description

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

P2297

00

A/F SENSOR1 (B1)

(O2 Sensor Out of Range During Deceleration Bank 1 Sensor 1)

Diagnosis condition

Engine run and fuel shut off

Signal

—

Threshold

Air fuel ratio (A/F) sensor 1 bank1 is out of normal range

Diagnosis delay time

—

POSSIBLE CAUSE

Air fuel ratio (A/F) sensor 1

FAIL-SAFE

Not applicable

Confirmation Procedure

Confirmation Procedure

  1. PRECONDITIONING

    If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

    1. Turn ignition switch OFF and wait at least 10 seconds.

    2. Turn ignition switch ON.

    3. Turn ignition switch OFF and wait at least 10 seconds.

    >>

    GO TO 2.

  2. PERFORM DTC CONFIRMATION PROCEDURE

    1. Start the engine and warm it up to normal operating temperature.

    2. Drive the Nissan Sentra vehicle a 80 km/h (50 MPH), with selecting suitable gear.

      Note:

      Always keep safe driving to the first priority.

    3. Release accelerator pedal completely to decelerate the Nissan Sentra vehicle for more than 10 seconds.

      Note:

      Always keep safe driving to the first priority.

    4. Check 1st trip DTC.

    Is 1st trip DTC detected?

    YES >>

    Refer to DTC Diagnosis Procedure.

    NO-1 >>

    To check malfunction symptom before repair: Refer to Intermittent Incident.

    NO-2 >>

    Confirmation after repair: INSPECTION END

Dtc Diagnosis Procedure

DTC Diagnosis Procedure

  1. CHECK AIR FUEL RATIO SENSOR 1 POWER SUPPLY

    1. Turn ignition switch OFF.

    2. Disconnect air fuel ratio (A/F) sensor 1 harness connector.

    3. Turn ignition switch ON.

    4. Check the voltage between A/F sensor 1 harness connector and ground.

      +

      −

      Voltage

      A/F sensor 1

      Connector

      Terminal

      F12

      4

      Ground

      Battery voltage

    Is the inspection result normal?

    YES >>

    GO TO 3.

    NO >>

    GO TO 2.

  2. CHECK AIR FUEL RATIO SENSOR 1 POWER SUPPLY CIRCUIT

    1. Turn ignition switch OFF.

    2. Disconnect IPDM E/R harness connector.

    3. Check the continuity between A/F sensor 1 harness connector and IPDM E/R harness connector.

      A/F sensor 1

      IPDM E/R

      Continuity

      Connector

      Terminal

      Connector

      Terminal

      F12

      4

      F96

      75

      Existed

    4. Also check harness for short to ground and short to power.

    Is the inspection result normal?

    YES >>

    Perform trouble diagnosis for power supply circuit.

    NO >>

    Repair or replace malfunctioning part.

  3. CHECK A/F SENSOR 1 INPUT SIGNAL CIRCUIT

    1. Turn ignition switch OFF.

    2. Disconnect ECM harness connector.

    3. Check the continuity between A/F sensor 1 harness connector and ECM harness connector.

      A/F sensor 1

      ECM

      Continuity

      Connector

      Terminal

      Connector

      Terminal

      F12

      1

      F25

      86

      Existed

      2

      88

    4. Check the continuity between A/F sensor 1 harness connector and ground, or ECM harness connector and ground.

      A/F sensor 1

      —

      Continuity

      Connector

      Terminal

      F12

      1

      Ground

      Not existed

      2

      ECM

      —

      Continuity

      Connector

      Terminal

      F25

      86

      Ground

      Not existed

      88

    5. Also check harness for short to ground and short to power.

    Is the inspection result normal?

    YES >>

    GO TO 4.

    NO >>

    Repair or replace malfunctioning part.

  4. REPLACE A/F SENSOR 1

    Replace malfunctioning A/F sensor 1. Refer to Exploded View.

    >>

    INSPECTION END

    P2271 O2 Sensor 2 Bank 1
    Dtc Description DTC Description DTC DETECTION LOGIC The heated oxygen sensor 2 has a much longer switching time between rich and lean than the air fuel ratio (A/F) sensor 1. The...
    P2610 Ecm Internal Timer
    Dtc Description DTC Description This ECM contains a timer and measures time between an ignition switch OFF and the next ignition switch ON. This enables the judging of the state...

    Other materials:

    Torque Converter Clutch Solenoid Circuit
    Diagnosis Procedure Diagnosis Procedure CHECK HARNESS CONNECTOR Ignition switch OFF. Check the mating condition of TCM harness connector and CVT unit harness connector. Is the inspect ...

    Basic Inspection
    Diagnosis and Repair Workflow Work Flow Work Flow OVERALL SEQUENCE DETAILED FLOW GET INFORMATION FOR SYMPTOM Get detailed information from the customer about the symptom (the condition and the environment when the incident/ma ...

    Engine cooling system
    The engine cooling system of the Nissan Sentra is factory-filled with a pre-diluted mixture consisting of 50% Genuine NISSAN Long Life Antifreeze/Coolant (blue) and 50% water. This formulation is designed to provide reliable, year-round antifreeze protection and effective engine cooling perfor ...