S Nissan Sentra Manuals Library
Factory-style information for owners and repair work

Nissan Sentra techinfo

Find Nissan Sentra owner information, maintenance instructions, technical references, service procedures and useful repair pages in one clean online library.

Quick access Sentra Docs
B18 Owner's 2020-2025 Sentra owner information B18 Service 2020-2025 Sentra Workshop manual B17 Owner's 2013-2019 Sentra owner documentation B17 Service 2013-2019 Sentra service information

Nissan Sentra B18 (2020-2025) Service Manual: P0796-00 Pressure Control Solenoid C

Dtc Description

DTC Description

DTC DETECTION LOGIC

DTC

CONSULT screen terms

(Trouble diagnosis content)

DTC detection condition

P0796

00

PRESSURE CONTROL SOLENOID C

(Pressure Control Solenoid "C" Performance/Stuck Off)

1

Diagnosis conditions

Diagnosis is permitted when all of the following conditions are satisfied:

a) Ignition voltage ≥ 9.01 V

b) Battery voltage ≥ 9.01 V

c) CVT fluid temperature ≥ -20 °C (-4 °F)

d) Lock-up pattern: Lock-up ON or Lock-up OFF

e) Engine speed > 450 rpm

Signal

—

Threshold

When the following conditions "a" and "b" are satisfied for the specified period [5 sec] continuously.

Keep the same conditions for specified period again after interval.

a) Secondary pulley sensor pressure < Line pressure sensor pressure - Variation

b) Secondary pulley sensor pressure < Secondary pulley sensor instruction pressure - Variation

[Interval]

  • Movement of target pressure

    ⇒ Target pressure under satisfied oil pressure difference judgement - Current target pressure ≥ 1 MPa

  • Stop valid judgement ⇒ Nissan Sentra Vehicle speed ≤ 3 km/h (2 MPH)

Diagnosis delay time

5 seconds × 2 count

2

Diagnosis conditions

Diagnosis is permitted when all of the following conditions are satisfied:

a) Engine speed > 625 rpm

b) Shift position: Other than P/N position

c) CVT fluid temperature ≥ -20 °C (-4 °F)

d) Power supply voltage ≥ 10 V

e) A drop in secondary pressure is detected during steady state. (Both "e-1" and "e-2" are satisfied twice in the same DC. There is an interval of 30 seconds between the first and second judgment):

e-1) When all of the following condition are satisfied and this state is maintained for 1.52 seconds:

e-1-1) Current accelerator opening - Accelerator opening when secondary pressure drop is judged ≤ 5 deg

e-1-2) Current Nissan Sentra vehicle speed - Vehicle speed when secondary pressure drop is judged ≤ 15 km/h

e-2) When all of the following condition are satisfied and this state is maintained for 1.52 seconds:

e-2-1) Actual secondary pressure < oil balance low limit pressure

e-2-2) Instruction pressure of secondary pressure after filtering - Actual secondary pressure: More than 0.25 MPa

Signal

—

Threshold

Instruction pressure of secondary pressure - Actual secondary pressure: 1.2 MPa or more

Diagnosis delay time

10 seconds

3

Diagnosis conditions

Diagnosis is permitted when all of the following conditions are satisfied:

a) Engine speed > 625 rpm

b) Shift position: Other than P/N position

c) CVT fluid temperature ≥ -20 °C (-4 °F)

d) Power supply voltage ≥ 10 V

e) A drop in secondary pressure is detected during the transitional period. (Both "e-1" and "e-2" are satisfied)

e-1) When all of the following condition are satisfied and this state is maintained for 1 second:

e-1-1) Actual secondary pressure < oil balance low limit pressure

e-1-2) Instruction pressure of secondary pressure after filtering - Actual secondary pressure: More than 0.25 MPa

e-2) When any of the following conditions are satisfied

e-2-1) Oil balance pressure - Actual secondary pressure ≥ 2 MPa

e-2-2) Instruction secondary pressure - Actual secondary pressure ≥ 2 MPa

Signal

—

Threshold

Instruction pressure of secondary pressure - Actual secondary pressure: 1.2 MPa or more

Diagnosis delay time

10 seconds
Note:

DC stands for “DRIVING CYCLE” and indicates a series of driving cycle of “Ignition switch OFF → ON → driving → OFF”.

POSSIBLE CAUSE

  • Harness or connector

  • Secondary pressure solenoid valve

  • Control valve

  • TCM

FAIL-SAFE

  • Nissan Sentra Vehicle speed < 40 km/h (25 MPH) or Input speed < 1300 rpm

    • Selector shock is large

    • Start is slow

    • Acceleration is slow

    • Lock-up is not performed

    • Nissan Sentra Vehicle speed is not increased

    • Stop/start system prohibited

  • Other then the above

    • Selector shock is large

    • Start is slow

    • Acceleration is slow

    • Nissan Sentra Vehicle speed is not increased

    • Stop/start system prohibited

DTC CONFIRMATION PROCEDURE

  1. PREPARATION BEFORE WORK

    If another "DTC CONFIRMATION PROCEDURE" occurs just before, ignition switch OFF and wait for at least 10 seconds, then perform the next test.

    TESTING CONDITION:

    Before performing the following procedure, confirm that battery voltage is more than 10 V.

    >>

    GO TO 2.

  2. CHECK DTC DETECTION

    1. Start the engine.

    2. Drive the Nissan Sentra vehicle and maintain the following conditions for 20 seconds or more.

      Shift position

      : "D" position

      CVT fluid temperature

      : 25 °C (77 °F) - 120 °C (248 °F)

      Nissan Sentra Vehicle speed

      : 40 km/h (25 MPH) or more

      CAUTION:

      Be careful of the driving speed.

    3. Stop the Nissan Sentra vehicle and wait at least 30 seconds.

    4. Repeat step 2 to 3.

    5. Check the DTC.

    Is "P0796-00" detected?

    YES >>

    Proceed to Diagnosis Procedure.

    NO-1>>

    To check malfunction symptom before repair: Refer to Intermittent Incident.

    NO-2>>

    Confirmation after repair: INSPECTION END

Diagnosis Procedure

Diagnosis Procedure

  1. INSPECT CVT STEEL BELT

    Inspect the CVT steel belt. Refer to Component Inspection.

    Is CVT steel belt OK?

    YES >>

    GO TO 2.

    NO >>

    GO TO 4.

  2. CHECK SECONDARY PRESSURE SOLENOID VALVE CIRCUIT - 1

    1. Disconnect TCM harness connector.

    2. Disconnect CVT unit harness connector.

    3. Check resistance between TCM harness connector terminal and CVT unit harness connector terminal.

      TCM

      CVT unit

      Resistance

      Connector

      Terminal

      Connector

      Terminal

      F23

      39

      F46

      3

      1 Ω or less
       

    Is the inspection result normal?

    YES >>

    GO TO 3.

    NO >>

    Repair harness or connector.

  3. REPLACE CONTROL VALVE

    Replace control valve. Refer to Removal and Installation.

    >>

    GO TO 6.

  4. CHECK SECONDARY PRESSURE SOLENOID VALVE CIRCUIT - 2

    1. Disconnect TCM harness connector.

    2. Disconnect CVT unit harness connector.

    3. Check resistance between TCM harness connector terminal and CVT unit harness connector terminal.

      TCM

      CVT unit

      Resistance

      Connector

      Terminal

      Connector

      Terminal

      F23

      39

      F46

      3

      1 Ω or less
       

    Is the inspection result normal?

    YES >>

    GO TO 5.

    NO >>

    1. Repair harness or connector.

    2. GO TO 5.

  5. REPLACE BELT AND PULLEYS

    Replace belt and pullesy. Refer to Disassembly and Assembly.

    >>

    GO TO 6.

  6. CHECK DTC DETECTION

    Perform DTC confirmation procedure. Refer to DTC Description.

    Is "P0796-00" detected again?

    YES >>

    Replace TCM. Refer to Removal and Installation.

    NO >>

    INSPECTION END

    P0747-00 Pressure Control Solenoid a
    Dtc Description DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0747 00 PRESSURE CONTROL SOLENOID A (Pressure C...
    P0845-00 Transmission Fluid Pressure Sensor/switch a
    Dtc Description DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0845 00 FLUID PRESS SEN/SW A (Transmission Flui...

    Other materials:

    Primary Pressure Solenoid Valve Circuit
    Diagnosis Procedure Diagnosis Procedure CHECK HARNESS CONNECTOR Ignition switch OFF. Check the mating condition of TCM harness connector and CVT unit harness connector. Is the inspect ...

    Reference Value
    Reference Value TERMINAL LAYOUT PHYSICAL VALUES Terminal No. (Wire color) Description Condition Value ...

    C1741-21 Tire Pressure Sensor No Data Fl
    Dtc Description DTC Description Note: The Signal Tech II Tool [– (NI-50190)] can be used to perform the following functions: Refer to the Signal Tech II User Guide for additional information. Activate and display TPMS sensor IDs Display tire pressure rep ...