Nissan Sentra B18 (2020-2025) Service Manual / Engine / Work Procedure (After Replacing Electric Throttle Control Actuator) / Dtc/circuit Diagnosis / P0262 Fuel Injector (cylinder 1)

Nissan Sentra B18 (2020-2025) Service Manual: P0262 Fuel Injector (cylinder 1)

Dtc Description

DTC Description

DTC DETECTION LOGIC

DTC	CONSULT screen terms (Trouble diagnosis content)	DTC detection condition
P0262	CYL1 INJECTOR (Cylinder 1 Injector A Circuit High)	Diagnosis condition	—
		Signal (terminal)	—
		Threshold	Direct injector driver unit is malfunctioning. ECM detects direct fuel injector No. 1 circuit is shorted.
		Diagnosis delay time	—

POSSIBLE CAUSE

Harness or connectors
- Direct fuel injector circuit is shorted
Battery power supply
ECM (direct injector driver unit)
direct fuel injector

FAIL-SAFE

Engine Control System

Engine operating condition in fail-safe mode
Fail safe mode		Nissan Sentra Vehicle behavior
Traveling control mode	Accelerator angle variation control	ECM controls the accelerator pedal depression speed to make it slower than actual speed. This causes a drop in accelerating performance and encourages the driver to repair malfunction. Note: ECM does not control the accelerator pedal releasing speed.
Device fix mode		This mode fixes the EVT control solenoid valve in the reference position. The intake manifold runner control valve motor is turned OFF (intake manifold runner control valve opens).
Combustion control mode	Stratified charge combustion control at starting	No stratified charge combustion at starting (cold start).

Idle Start/Stop System

When a DTC is detected, the start/stop indicator lamp blinks slowly and the idle start/stop system operation is prohibited.

When ECM detects error while operating the idle start/stop system, ECM restarts the engine.

Confirmation Procedure

Confirmation Procedure

DTC CONFIRMATION PROCEDURE

PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
- Before performing the following procedure, confirm that battery voltage is between 12 - 15 V at idle.
>>
GO TO 2.
PERFORM DTC CONFIRMATION PROCEDURE
1. Start engine and let it idle for at least 20 seconds.
2. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >>
Refer to DTC Diagnosis Procedure.
NO-1 >>
To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2 >>
Confirmation after repair: INSPECTION END

Dtc Diagnosis Procedure

DTC Diagnosis Procedure

CHECK DIRECT FUEL INJECTOR

Check direct fuel injector. Refer to Component Function Check.

Is inspection result normal?
YES >>
GO TO 2.
NO >>
Repair or replace error-detected parts.
PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Erase DTC.
3. Perform DTC confirmation procedure again. Refer to Confirmation Procedure.
4. Check 1st trip DTC.
Is the DTC P0262 displayed again?
YES >>
Replace ECM. Refer to ECM : Removal & Installation.
NO >>
INSPECTION END

 P0261 Fuel Injector (cylinder 1)

Dtc Description DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P0261 CYL1 INJECTOR (Cylinder 1 Injector A Circu...

 P026b Injection Timing

Dtc Description DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition P026B Injection timing (Injection Timing Perform...

Other materials:

Camera Aiming Adjustment
Work Procedure Work Procedure Always adjust the camera aiming after removing and installing or replacing the front camera unit. Always adjust the camera aiming after removing and installing or replacing the windshield glass. CAUTION: ...

System Description
Component Parts Telematics System Component Parts Location Component Parts Location No. Component Function 1. ...

Magnet Clutch
Component Function Check Component Function Check CHECK MAGNET CLUTCH OPERATION Perform auto active test of IPDM E/R. Refer to CONSULT Function (IPDM E/R). Does it operate normally? YES >> Inspection End. NO > ...