Toyota Camry owners & service manuals

Toyota Camry (XV70): If the electronic key does not operate properly (vehicles with a smart key system)

Toyota Camry Owner's Manual XV70 (2017-2024) / When trouble arises / Steps to take in an emergency / If the electronic key does not operate properly (vehicles with a smart key system)

If communication between the electronic key and vehicle is interrupted or the electronic key cannot be used because the battery is depleted, the smart key system and wireless remote control cannot be used. In such cases, the doors and trunk can be opened and the engine can be started by following the procedure below.

Locking and unlocking the doors, unlocking the trunk and key linked functions

■ Doors

Using the mechanical key in order to perform the following operations (driver's door only):

  1. Locks all doors
  2. Closes the windows and the moon roof*1 or panoramic moon roof*1 (turn and hold)*2
  3. Unlocks the door
  4. Turning the key rearward unlocks the driver's door. Turning the key once again unlocks the other doors.
  5. Opens the windows and the moon roof*1 or panoramic moon roof*1 (turn and hold)*2

Steps to take in an emergency

*1: If equipped
*2: This setting must be customized at your Toyota dealer.

■ Trunk

Turn the mechanical key clockwise to open.

Steps to take in an emergency

Starting the engine

1. Ensure that the shift lever is in P and firmly depress the brake pedal.

2. Touch the Toyota emblem side of the electronic key to the engine switch.

When the electronic key is detected, a buzzer sounds and the engine switch will turn to IGNITION ON mode.

When the smart key system is deactivated in customization setting, the engine switch will turn to ACCESSORY mode.

Steps to take in an emergency

3. Firmly depress the brake pedal and check that is displayed on the multi-information display.

4. Press the engine switch shortly and firmly.

In the event that the engine still cannot be started, contact your Toyota dealer.

■Stopping the engine

Shift the shift lever to P and press the engine switch as you normally do when stopping the engine.

■Replacing the key battery

As the above procedure is a temporary measure, it is recommended that the electronic key battery be replaced immediately when the battery is depleted.

■Alarm (for Canada only)

Using the mechanical key to lock the doors will not set the alarm system.

If a door is unlocked using the mechanical key when the alarm system is set, the alarm may be triggered.

■Changing engine switch modes

Release the brake pedal and press the engine switch in step 3 above.

The engine does not start and modes will be changed each time the switch is pressed.

■When the electronic key does not work properly

  • Make sure that the smart key system has not been deactivated in the customization setting. If it is off, turn the function on.
  • Check if battery-saving mode is set. If it is set, cancel the function.

WARNING

■When using the mechanical key and operating the power windows or the moon roof or panoramic moon roof

Operate the power window or the moon roof or panoramic moon roof after checking to make sure that there is no possibility of any passenger having any of their body parts caught in the window or the moon roof or panoramic moon roof. Also, do not allow children to operate the mechanical key. It is possible for children and other passengers to get caught in the power window or the moon roof or panoramic moon roof.

    READ NEXT:

     If the vehicle battery is discharged

    The following procedures may be used to start the engine if the vehicle's battery is discharged. You can also call your Toyota dealer or a qualified repair shop. If you have a set of jumper (or b

     If your vehicle overheats

    The following may indicate that your vehicle is overheating. The needle of the engine coolant temperature gauge enters the red zone or a loss of engine power is experienced. (For example, the

     If the vehicle becomes stuck

    Carry out the following procedures if the tires spin or the vehicle becomes stuck in mud, dirt or snow: 1. Stop the engine. Set the parking brake and shift the shift lever to P. 2. Remove the mud,

    SEE MORE:

     Vehicle Speed Sensor (C1A45)

    DESCRIPTION The blind spot monitor sensor receives vehicle speed signals from the skid control ECU via CAN communication. Blind Spot Monitor Master DTC No. Detection Item DTC Detection Condition Trouble Area C1A45 Vehicle Speed Sensor A fail flag is transmitted from th

     How To Proceed With Troubleshooting

    CAUTION / NOTICE / HINT HINT: Use the following procedure to troubleshoot the navigation system. *: Use the Techstream. PROCEDURE 1. VEHICLE BROUGHT TO WORKSHOP NEXT 2. CUSTOMER PROBLEM ANALYSIS When troubleshooting, check th

    © 2023-2024 Copyright www.tocamry.com