Toyota Camry owners & service manuals

Toyota Camry: If your vehicle overheats

The following may indicate that your vehicle is overheating.

  • The needle of the engine coolant temperature gauge enters the red zone or a loss of engine power is experienced. (For example, the vehicle speed does not increase.)
  • "Engine Coolant Temp High Stop in a Safe Place See Owner's Manual" is shown on the multi-information display.
  • Steam comes out from under the hood.

Correction procedures

1. Stop the vehicle in a safe place and turn off the air conditioning system, and then stop the engine.

2. If you see steam: Carefully lift the hood after the steam subsides.

If you do not see steam: Carefully lift the hood.

3. After the engine has cooled down sufficiently, inspect the hoses and radiator core (radiator) for any leaks.

  1. Radiator
  2. Cooling fan

If a large amount of coolant leaks, immediately contact your Toyota dealer.

Steps to take in an emergency

4. The coolant level is satisfactory if it is between the "F" and "L" lines on the reservoir.

  1. Reservoir
  2. "F" line
  3. "L" line
  4. Radiator cap

2.5 L 4-cylinder (A25A-FKS) engine

Steps to take in an emergency

3.5 L V6 (2GR-FKS) engine

Steps to take in an emergency

5. Add coolant if necessary.

Water can be used in an emergency if coolant is unavailable.

2.5 L 4-cylinder (A25A-FKS) engine

Steps to take in an emergency

3.5 L V6 (2GR-FKS) engine

Steps to take in an emergency

6. Start the engine and turn the air conditioning system on to check that the radiator cooling fan operates and to check for coolant leaks from the radiator or hoses.

The fan operates when the air conditioning system is turned on immediately after a cold start. Confirm that the fan is operating by checking the fan sound and air flow. If it is difficult to check these, turn the air conditioning system on and off repeatedly. (The fan may not operate in freezing temperatures.)

7. If the fan is not operating: Stop the engine immediately and contact your Toyota dealer.

If the fan is operating: Have the vehicle inspected at the nearest Toyota dealer.

WARNING

■To prevent an accident or injury when inspecting under the hood of your vehicle

Observe the following precautions.

Failure to do so may result in serious injury such as burns.

  • If steam is seen coming from under the hood, do not open the hood until the steam has subsided. The engine compartment may be very hot.
  • Keep hands and clothing (especially a tie, a scarf or a muffler) away from the fan and belts. Failure to do so may cause the hands or clothing to be caught, resulting in serious injury.
  • Do not loosen the radiator cap and the coolant reservoir cap while the engine and radiator are hot.

    High temperature steam or coolant could spray out.

NOTICE

■When adding engine coolant

Wait until the engine has cooled down before adding engine coolant.

When adding coolant, do so slowly. Adding cool coolant to a hot engine too quickly can cause damage to the engine.

■To prevent damage to the cooling system

Observe the following precautions:

  • Avoid contaminating the coolant with foreign matter (such as sand or dust etc.).
  • Do not use any coolant additives.

    READ NEXT:

     If the vehicle becomes stuck

    Carry out the following procedures if the tires spin or the vehicle becomes stuck in mud, dirt or snow: 1. Stop the engine. Set the parking brake and shift the shift lever to P. 2. Remove the mud,

     Vehicle specifications

     Specifications

    SEE MORE:

     Removal

    REMOVAL PROCEDURE 1. REMOVE FRONT WHEEL OPENING EXTENSION PAD RH Click here 2. REMOVE FRONT WHEEL OPENING EXTENSION PAD LH Click here 3. REMOVE NO. 1 ENGINE UNDER COVER Click here 4. REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY Click here

     Vehicle Speed Signal Circuit between Stereo Component Amplifier and Combination Meter

    DESCRIPTION The stereo component amplifier assembly receives a vehicle speed signal from the combination meter assembly to control the ASL function. HINT: A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal

    © 2023-2024 Copyright www.tocamry.com