Nissan Sentra B18 (2020-2025) Service Manual / Steering / Steering Control System :: Dtc/circuit Diagnosis / C161c-86 Steering Angle Sensor System

Nissan Sentra B18 (2020-2025) Service Manual: C161c-86 Steering Angle Sensor System

Dtc Description

DTC Description

DTC DETECTION LOGIC

DTC No.	CONSULT screen terms (Trouble diagnosis content)	DTC detection condition
C161C-86	ST angle sensor system (Steering angle sensor system)	Diagnosis condition	When ignition switch is ON.
		Signal (terminal)	CAN communication signal
		Threshold	When a malfunction is detected in chassis control module (with built in steering angle sensor).
		Diagnosis delay time	2 seconds or more

POSSIBLE CAUSE

CAN communication line
Chassis control module (with built in steering angle sensor)
ABS actuator and electric unit (control unit)
EPS control unit

FAIL-SAFE

Normal control

Confirmation Procedure

PRECONDITIONING
1. If “Confirmation Procedure” has been previously conducted, always place the ignition switch OFF and wait at least 10 seconds before conducting the next test.
>>
GO TO 2.
DTC REPRODUCTION PROCEDURE
1. CONSULT
  1. Ignition switch ON.
  2. Select “Self Diagnostic Result” mode of “EPS/DAST 3”.
Is DTC “C161C-86” detected?
YES >>
Proceed to diagnosis procedure. Refer to DTC Diagnosis Procedure.
NO >>
To check malfunction symptom before repair: Refer to Intermittent Incident.
NO >>
Confirmation after repair: Inspection End.

Dtc Diagnosis Procedure

DTC Diagnosis Procedure

CHECK VEHICLE SPECIFICATION
1. Check vehicle specification.
>>
GO TO 2.
PERFORM SELF DIAGNOSTIC RESULT
1. 1. Ignition switch ON.
  2. Select “Self Diagnostic Result” mode of "CHASSIS CONTROL".
Is any DTC detected?
YES >>
Check the DTC. Refer to DTC Index.
NO >>
GO TO 3.
CHECK CONNECTOR AND TERMINAL
1. 1. Ignition switch OFF.
  2. Disconnect chassis control module harness connector.
  3. Disconnect EPS control unit harness connector.
  4. Check the connector for disconnection or looseness.
  5. Check the pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES >>
GO TO 4.
NO >>
Repair or replace harness, connector, or terminal, securely lock the connector.
PERFORM SELF DIAGNOSTIC RESULT
1. CONSULT
  1. Connect chassis control module harness connector.
  2. Connect EPS control unit harness connector.
  3. Ignition switch ON.
  4. Erase "Self Diagnostic Result" mode of "EPS/DAST 3".
  5. Ignition switch OFF and wait for at least 10 seconds.
  6. Ignition switch ON.
  7. Select “Self Diagnostic Result” mode of “EPS/DAST 3”.
Is DTC “C161C-86” detected?
YES>>
EPS control unit is malfunctioning. Replace steering gear column assembly. Refer to Removal and Installation.
NO>>
Inspection End.

 C161c-83 Steering Angle Sensor System

Dtc Description DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C161C-83 ST angle sensor system (Steering an...

 C161c-87 Steering Angle Sensor System

Dtc Description DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detection condition C161C-87 ST angle sensor system (Steering an...

Other materials:

Removal and Installation
Ecm Ecm : Exploded View ECM : Exploded View 1. Bracket 2. ECM Ecm : ...

Microphone Signal Circuit
Diagnosis Procedure Diagnosis Procedure CHECK HARNESS BETWEEN AV CONTROL UNIT AND MICROPHONE Ignition switch OFF. Disconnect AV control unit connector and microph ...

P161f Immobilizer
Dtc Description DTC Description DTC DETECTION LOGIC DTC No. CONSULT screen items (Trouble diagnosis content) DTC detecting condition ...