Nissan Sentra Service Manual: U0155 Lost communication (IPC)

Nissan Sentra Service Manual / Transmission & driveline / Transaxle & transmission / CVT: RE0F11A / U0155 Lost communication (IPC)

DTC Logic

DTC DETECTION LOGIC

DTC	CONSULT screen terms [Trouble diagnosis content]	DTC detection condition	Possible causes
U0155	LOST COMM (IPC) [Lost Communication With Instrument Panel Cluster (IPC) Control Module]	When the ignition switch is ON, TCM is unable to receive the CAN communications signal from the combination meter continuously for 2 seconds or more.	Combination meter Harness or connector (CAN communication line is open or shorted)

DTC CONFIRMATION PROCEDURE

1.PREPARATION BEFORE WORK

If another вЂњDTC CONFIRMATION PROCEDUREвЂќ occurs just before, turn ignition switch OFF and wait for at least 10 seconds, then perform the next test.

>> GO TO 2.

2.PERFORM DTC CONFIRMATION PROCEDURE

With CONSULT

Start the engine and wait for at least 5 seconds.
Check the DTC.

Is вЂњU0155вЂќ detected? YES >> Go to TM-156, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

For the diagnosis procedure, refer to LAN-16, "Trouble Diagnosis Flow Chart".

U0300 CAN COMMUNICATION DATA

DTC Logic

DTC DETECTION LOGIC

DTC	CONSULT screen terms (Trouble diagnosis content)	DTC detection condition	Possible causes
U0300	CAN COMM DATA (Internal Control Module Software Incompatibility)	When the ignition switch is ON, the data length transmitted from each control unit is shorter than the specified length and the status continues for 2 seconds or more.	Control unit other than TCM

DTC CONFIRMATION PROCEDURE

1.PREPARATION BEFORE WORK

If another вЂњDTC CONFIRMATION PROCEDUREвЂќ occurs just before, turn ignition switch OFF and wait for at least 10 seconds, then perform the next test.

>> GO TO 2.

2.CHECK DTC DETECTION

With CONSULT

Start the engine and wait for 5 seconds or more.
Check the DTC.

Is вЂњU0300вЂќ detected? YES >> Go to TM-157, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CONTROL UNIT CHECK

Check the number of control units replaced before вЂњU0300вЂќ is detected.

Is one control unit replaced? YES >> The specification of the control unit replaced may be incorrect. Check the part number and the specification.

NO >> GO TO 2.

2.CONTROL UNIT CHECK

With CONSULT

Remove one of the control unit replaced
Assemble the old control unit before replacement.
Turn ignition switch ON, and wait for 2 seconds or more.
Select вЂњSelf Diagnostic ResultsвЂќ in вЂњTRANSMISSIONвЂќ.

Is вЂњU0300вЂќdetected? YES >> Turn OFF the ignition switch and check other control units in the same manner.

NO >> The specification of the control unit removed may be incorrect. Check the part number and the specification.

U0140 Lost communication (BCM)

DTC Logic DTC DETECTION LOGIC DTC CONSULT screen terms [Trouble diagnosis content] DTC detection condition Possible causes U0140 LOST COMM (BCM) [Lost Communication ...

U1000 Can comm circuit

Description CAN (Controller Area Network) is a serial communication line for real-time application. It is an on-vehicle multiplex communication line with high data communication speed and excelle ...

Other materials:

ECU diagnosis information
A/C AUTO AMP Reference Value VALUES ON THE DIAGNOSIS TOOL TERMINAL LAYOUT PHYSICAL VALUES DTC Inspection Priority Chart If some DTCs are displayed at the same time, perform inspections one by one based on the following priority chart. DTC Index *: Perform self ...

Driving on snow or ice
WARNING Wet ice (32°F, 0°C and freezing rain), very cold snow or ice can be slick and very hard to drive on. The vehicle will have much less traction or “grip” under these conditions. Try to avoid driving on wet ice until the road is salted or sanded. Wha ...

Precaution
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" The supplemental restraint system such as вЂњair bagвЂќ and вЂњseat belt pre-tensionerвЂќ, used along with a front seat belt, helps to reduce the risk or severity of injur ...