Nissan Sentra manuals

Nissan Sentra Service Manual: Turn signal lamp circuit

Description

The bcm monitors inputs from the combination switch to determine when to activate the turn signals. The bcm outputs voltage direction to the left and right turn signals during turn signal operation or both during hazard warning operation. The bcm sends a turn signal indicator request to the combination meter via the can communication lines.

The bcm performs the fast flasher operation (fail-safe) if any bulb or harness of the turn signal lamp circuit is open.

Note:

Turn signal lamp blinks at normal speed when using the hazard warning lamp.

Component function check

1.Check turn signal lamp

Consult


  1. Select FLASHER of BCM (FLASHER) active test item.
  2. With operating the test items, check that the turn signal lamp blinks.

Lh : turn signal lamps (lh) on

Rh : turn signal lamps (rh) on

Off : the turn signal lamps off

Does the turn signal lamp blink? Yes >> turn signal lamp circuit is normal.

No >> refer to exl-99, "diagnosis procedure".

Diagnosis procedure

Regarding wiring diagram information, refer to exl-58, "wiring diagram".

1.Check turn signal lamp bulb

Check the applicable lamp bulb to be sure the proper bulb standard is in use and the bulb is not open.

Is the bulb ok? Yes >> go to 2.

No >> replace the bulb.

2.Check turn signal lamp output voltage

  1. Turn the ignition switch off.
  2. Disconnect the front or rear combination lamp harness connector or the door mirror harness connector (if equipped with turn signal in mirror) in question.
  3. Turn the ignition switch on.
  4. Operate the turn signal switch.
  5. While the turn signal is operating, check the voltage between the front combination lamp harness connector and ground.



  1. While the turn signal is operating, check the voltage between the rear combination lamp harness connector and ground.


  1. While the turn signal is operating, check the voltage between the door mirror harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? Yes >> go to 5.

No >> go to 3.

3.Check turn signal lamp circuit for open

  1. Turn the ignition switch off.
  2. Disconnect bcm harness connector in question.
  3. Check continuity between the bcm harness connector and the front combination lamp harness connector.


  1. Check continuity between the BCM harness connector and the rear combination lamp harness connector.


  1. Check continuity between the BCM harness connector and the door mirror harness connector in question.

Is the inspection results normal?


Is the inspection results normal? YES >> GO TO 4.

NO >> Repair or replace the harness or connectors.

4.Check turn signal lamp short circuit

  1. Check continuity between the bcm harness connector and ground.

Are the inspection results normal?


Are the inspection results normal? YES >> Replace BCM. Refer to BCS-73, "Removal and Installation" (with Intelligent Key system) or BCS- 126, "Removal and Installation" (without Intelligent Key system).

NO >> Repair or replace the harness or connectors.

5.Check turn signal lamp ground circuit

  1. Turn the ignition switch OFF.
  2. Check continuity between the front combination lamp harness connector or the rear combination lamp harness connector or the door mirror harness connector in question and ground.



  1. Check continuity between the rear combination lamp harness connector and ground.


  1. Check continuity between the door mirror harness connector and ground.

Are the inspection results normal?


Are the inspection results normal? YES >> Replace the malfunctioning lamp.

NO >> Repair or replace the harness or connectors.

Parking lamp circuit
Description The ipdm e/r (intelligent power distribution module engine room) controls the tail lamp relay based on inputs from the bcm over the can communication lines. When the tail lamp relay i ...

Optical sensor
Description The optical sensor measures ambient light and transmits the optical sensor signal to the bcm. Component function check 1.Check optical sensor signal by consult Consult Turn the ...

Other materials:

System description
Component parts Component parts location Instrument lower finisher Component description Eco mode switch The ECO mode switch is installed to the instrument lower finisher. When the eco mode indicator lamp on the combination meter is off and the eco mode switch is pressed, t ...

Electric parking brake
A mode can be selected from the following modes. Automatic mode The parking brake is set or released automatically according to the shift lever operation. Even when in automatic mode, the parking brake can be set and released manually. Turns automatic mode on (while the vehicle is stopp ...

Tilt operation
Pull the lock lever down 1 and adjust the steering wheel up or down 2 to the desired position. Push the lock lever up 1 firmly to lock the steering wheel in place. WARNINGDo not adjust the steering wheel while driving. You could lose control of your vehicle and cause an accide ...

В© 2014-2024 Copyright www.nisentra.com