Nissan Sentra Service Manual: Road wheel tire assembly
Exploded View
Removal and Installation
REMOVAL
- Remove wheel nuts.
- Remove wheel and tire.
INSTALLATION
Installation is in the reverse order of removal.
Adjustment
BALANCING WHEELS (ADHESIVE WEIGHT TYPE)
Preparation Before Adjustment
Remove inner and outer balance weights from the road wheel. Using releasing
agent, remove double-faced
adhesive tape from the road wheel.
CAUTION:
- Be careful not scratch the road wheel during removal.
- After removing double-faced adhesive tape, wipe clean all traces
of releasing agent from the road
wheel.
Wheel Balance Adjustment
- Set road wheel on balancer machine using the center hole as a guide.
Start the balancer machine.
- For balancer machines that only have a clip-on (rim flange) weight mode
setting, follow this step to calculate
the correct size adhesive weight to use. When inner and outer imbalance
values are shown on the
balancer machine indicator, multiply outer imbalance value by 5/3 (1.67) to
determine balance weight that
should be used. Select the outer balance weight with a value closest to the
calculated value above and
install in to the designated outer position of, or at the designated angle
in relation to the road wheel.
- Indicated imbalance value × 5/3 (1.67) = balance weight to be
installed
Calculation example:
23 g (0.81 oz) × 5/3 (1.67) = 38.33 g (1.35 oz) ⇒ 40 g (1.41 oz)
balance weight (closer to calculated balance weight value)
NOTE:
Note that balance weight value must be closer to the calculated
balance weight value.
Example:
37.4 ⇒ 35 g (1.23 oz)
37.5 ⇒ 40 g (1.41 oz)
- Install balance weight in the position shown.
CAUTION:
- Do not install the inner balance weight before installing
the outer balance weight.
- Before installing the balance weight, be sure to clean the
mating surface of the road wheel.
- When installing balance weight (1) to road wheel, set it into the
grooved area (A) on the inner wall of the road wheel as shown
so that the balance weight center (B) is aligned with the balancer
machine indication position (angle) (C).
CAUTION:
- Always use genuine NISSAN adhesive balance weights.
- Balance weights are non-reusable; always replace with
new ones.
- Do not install more than three sheets of balance weight.
- If calculated balance weight value exceeds 50 g (1.76 oz), install
two balance weight sheets in line with each other as shown.
CAUTION:
Do not install one balance weight sheet on top of another.
- Start balancer machine again.
- Install balance weight on inner side of road wheel in the balancer
machine indication position (angle).
CAUTION:
Do not install more than two balance weights.
- Start balancer machine. Make sure that inner and outer residual
imbalance values are 5 g (0.18 oz) each or below.
- If either residual imbalance value exceeds 5 g (0.18 oz), repeat
installation procedures.
Allowable imbalance Refer to WT-54, "Road Wheel".
TIRE ROTATION
CAUTION:
- Do not include the T-type spare tire when rotating the tires.
- When installing wheels, tighten them diagonally by dividing
the work two to three times in order to prevent the wheels
from developing any distortion.
- Be careful not to tighten wheel nut at torque exceeding the
criteria for preventing strain of disc rotor.
- Use NISSAN genuine wheel nuts for aluminum wheels.
Wheel nut tightening torque Refer to WT-54, "Road Wheel".
Exploded View
Transmitter (tire pressure sensor)
O-ring
Valve stem nut
Valve core
Valve cap
Valve stem assembly
Parts that are replaced as a set
when the tire is replaced.
Remo ...
Other materials:
P0506 ISC System
Description
The ECM controls the engine idle speed to a specified level through the fine
adjustment of the air, which is let
into the intake manifold, by operating the electric throttle control actuator.
The operating of the throttle valve is
varied to allow for optimum control of the engine ...
Warning signals
To help prevent the vehicle from moving unexpectedly
by erroneous operation of the Intelligent
Key or to help prevent the vehicle from being
stolen, a chime or buzzer sounds from inside and
outside the vehicle and a warning light comes on
in the instrument panel.
When a chime or beep sounds ...
Parking brake shoe
Adjustment - Drum Brake
If equipped with drum brakes, refer to PB-11, "Inspection and
Adjustment".
Adjustment - Disc Brake
Adjust parking brake lever stroke. Refer to PB-4,
"Inspection and Adjustment".
Perform parking brake break-in (drag on) operation by
d ...
В© 2014-2024 Copyright www.nisentra.com