Nissan Sentra Service Manual: Precaution for Brake Control System
-
Always perform a pre-driving check to drive the vehicle.
-
Always check speed and safety while driving the vehicle.
-
To operate CONSULT while driving, more than one person is required to be in the vehicle to avoid interference to driving and ensure safety.
-
Slight vibrations are felt on the brake pedal and the operation noises occur, when ABS function or EBD function operates. This is not a malfunction because it is caused by ABS function or EBD function that is normally operated.
-
When starting engine or when starting vehicle just after starting engine, brake pedal may vibrate or motor operating noise may be heard from engine compartment. This is normal condition.
-
Brake stopping distance may become longer than models without ABS function depending on the road conditions, when ABS function is operated on slippery road like rough road, gravel road or snowy road
-
When a malfunction is indicated, always collect information from the customer about conditions of occurrence, estimate cause and perform operation. Check brake booster operation, brake fluid level and brake fluid leakage, as well as electrical system.
-
The optimum performance is achieved by control for ABS function or EBD function when all of brakes, suspensions and tires installed on the vehicle are the specified size and parts. Brake performance and controllability may be negatively affected when other parts than the specified are installed.
-
Brake stopping distance may become longer and steering stability may be negatively affected, when tires in different size and combination or other parts than the specified are used.
-
When a radio (including wiring), antenna and antenna lead line are located near ABS actuator and electric unit (control unit), a malfunction or improper operation may occur for the control of ABS function or EBD function.
-
When the following items are replaced by other parts than genuine parts or modified, ABS warning lamp and brake warning lamp may turn ON, and the control may not operate normally for ABS function or EBD function.
-
Suspension component parts (shock absorber, spring, bushing and others)
-
Tire and wheel (other than the specified size)
-
Brake component parts (brake pad, disc rotor, brake caliper and others)
-
Engine component parts (ECM, muffler and others)
-
Body reinforcement component parts (rollover bar, tower bar and others)
-
When suspension, tire and brake component parts are excessively worn or deteriorated and the vehicle is driven, ABS warning lamp and brake warning lamp may turn ON, and the control may not operate normally for ABS function or EBD function.
-
ABS warning lamp and brake warning lamp may turn ON, when only front wheel or rear wheel is rotated using a free roller. This is not a malfunction, because it is caused by wheel speed difference between wheel that is rotated and wheel that is not rotated. In this case, perform self-diagnosis, check self-diagnosis results, and erase memory.
-
When power supply voltage is not normal, ABS warning lamp and brake warning lamp turn ON. ABS actuator and electric unit (control unit) stops control for ABS function or EBD function. Ordinary brake operates.
After power supply returns to normal, ABS warning lamp and brake warning lamp turn OFF. The control becomes operative for ABS function or EBD function.
Precaution for Supplemental Restraint System (SRS) "AIR BAG"
and "SEAT BELT PRE-TENSIONER"
The Supplemental Restraint System such as “AIR BAG” and “SEAT
BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the
dri ...
Precaution for Harness Repair
Solder the repair part, and wrap it with tape. [Twisted wire
fray
must be 110 mm (4.33 in) or less.]
Do not bypass the repair point with wire. (If it is
bypassed, the turnou ...
Other materials:
Main line between dlc and hvac circuit
Diagnosis Procedure
1.Check harness continuity (open circuit)
Turn the ignition switch OFF.
Disconnect the battery cable from the negative terminal.
Disconnect the following harness connectors.
Ecm
A/c auto amp.
Check the continuity between the data link connector and the a/c ...
Precaution for Work
When removing or disassembling each component, be careful not to damage
or deform it. If a component
may be subject to interference, be sure to protect it with a shop cloth.
When removing (disengaging) components with a screwdriver or similar
tool, be sure to wrap the component
with a ...
Checking bulbs
With all doors closed, apply the parking brake
and place the ignition switch in the ON position
without starting the engine. The following lights
will come on:
If equipped, the following lights come on briefly
and then go off:
If any light fails to come on, it may indicate
an open circuit ...
