Nissan Sentra manuals

Nissan Sentra Service Manual: Parking brake shoe

Removal and Installation - Drum Brake

If equipped with drum brakes, refer to BR-42, "Removal and Installation".

Exploded View - Disc Brake


  1. Anti-rattle pin

  2. Back plate

  3. Toggle lever

  4. Parking brake shoe

  5. Brake strut

  6. Return spring

  7. Spring

  8. Adjuster

Butyl Cuprysil) Apply PBC (Poly
Butyl Cuprysil) grease or silicone based grease

Removal and Installation - Disc Brake

REMOVAL

WARNING:

Clean dust on the parking brake shoes with a vacuum dust collector to minimize the hazard of air borne particles or other materials.

  1. Remove rear wheels and tires using power tool. Refer to WT-47, "Adjustment".

  2. Remove disc rotor. Refer to RAX-7, "Removal and Installation - Disc brake".

CAUTION:

Parking brake must be completely released before removing rotor.

  1. Remove return springs (1) from the top of the parking brake shoes.


  1. Remove the return spring (1) from the lower side of the parking brake shoes.


  1. Remove springs (1) from the parking brake shoes.

CAUTION:

Do not drop the removed parts.

  1. Remove parking brake shoes, adjuster, brake strut and toggle lever.

CAUTION:


  1. Press the rear cable spring (1) against spring tension to remove rear cable (3) from the clamp (A) of toggle lever (2).

CAUTION:

Do not bend rear cable.

  1. Remove back plate (if necessary). Refer to RAX-7, "Removal and Installation - Disc brake".

INSTALLATION


INSTALLATION

Installation is in the reverse order of removal.

CAUTION:

The front parking brake shoes are made of different materials than the rear parking brake shoes.

Install the parking brake shoes in the proper location.

(A) : For (RH) brake

(B) : For (LH) brake

: Adjuster expands : Front


: Adjuster expands



Inspection and Adjustment


Inspection and Adjustment

INSPECTION AFTER REMOVAL

Lining Thickness Inspection

Wear limit thickness : Refer to PB-13, "Parking Drum Brake".

Drum Inner Diameter Inspection


Drum Inner Diameter Inspection

Wear limit of inner diameter : Refer to PB-13, "Parking Drum Brake".

Other Inspections


Other Inspections

Check the following items, and replace the parts if necessary.

ADJUSTMENT AFTER INSTALLATION

  1. Adjust the parking brake lever stroke. Refer to PB-4, "Inspection and Adjustment".

  2. Rotate the disc rotor to check that there is no drag. Install the plug. If any drag is found, follow the procedure described below.

  1. Adjust parking brake stroke again.

  2. Check rear disc brake.

  1. Adjust the parking brake shoe. Refer to PB-6, "Adjustment - Disc Brake".

Parking brake control
Exploded View Parking brake lever assembly Adjusting nut Parking brake switch Front parking brake cable Rear parking brake cable (LH) Rear parking brake cable (RH) ...

Service data and specifications (SDS)
Parking Drum Brake Parking Brake Control ...

Other materials:

Camshaft valve clearance
Inspection and Adjustment INSPECTION Perform inspection after removal, installation or replacement of camshaft or valve-related parts, or if there are unusual engine conditions regarding valve clearance. Remove rocker cover. Refer to EM-46, "Exploded View". Measure the valve cle ...

Vehicle security system (if so equipped)
The vehicle security system provides visual and audible alarm signals if someone opens the doors when the system is armed. It is not, however, a motion detection type system that activates when a vehicle is moved or when a vibration occurs. The system helps detect vehicle theft but cannot prev ...

U1000 CAN Comm circuit
DTC Logic DTC DETECTION LOGIC DTC Display Item Malfunction detected condition Possible causes U1000 CAN COMM CIRCUIT When CAN communication signal is not continuously received for 2 seconds or more CAN communication system malfunction Diagnosis Procedure ...

В© 2014-2024 Copyright www.nisentra.com