Nissan Sentra manuals

Nissan Sentra Service Manual: P285A Clutch B Pressure

Nissan Sentra Service Manual / Transmission & driveline / Transaxle & transmission / CVT: RE0F11A / P285A Clutch B Pressure

DTC Logic

DTC DETECTION LOGIC

DTC

 CONSULT screen terms (Trouble diagnosis content)

 DTC detection condition

 Possible causes
P285A CLUTCH B PRESSURE (Clutch B Pressure Disengagement Performance) The detection conditions continuously for 200 msec or more under the following diagnosis conditions:

Diagnosis conditions

  • Selector lever: Other than “P”, “R” and “N” positions
  • Vehicle speed: 10 km/h (6 MPH) or more
  • Engine speed: More than 550 rpm
  • Output speed: More than 300 rpm
  • Secondary pulley speed: More than 300 rpm
  • A lapse of 500 msec or more after the stop lamp switch is turned from ON to OFF.
  • Command for the 1GR of auxiliary gearbox is in progress
  • Auxiliary gearbox shifting is not in progress.
  • TCM power supply voltage: More than 11 V

Detection conditions

  • Acceleration/deceleration: Less than −0.05 G
  • Actual auxiliary gearbox gear ratio − Auxiliary gearbox 1GR ratio ≥ 50%
  • High clutch & reverse brake solenoid valve
  • Control valve assembly
The auxiliary gearbox gear ratio is В±10% or less for the auxiliary gearbox 2GR ratio continuously for 500 msec or more under the following diagnosis conditions:

Diagnosis conditions

  • Selector lever: Other than “P”, “R” and “N” positions
  • Accelerator pedal position: 0.7/8 or more
  • Engine speed: More than 550 rpm
  • Secondary pulley speed: More than 300 rpm
  • Output speed: More than 300 rpm
  • Command for the 1GR of auxiliary gearbox is in progress
  • Auxiliary gearbox shifting is not in progress
  • TCM power supply voltage: More than 11 V

DTC CONFIRMATION PROCEDURE

CAUTION:

1.PREPARATION BEFORE WORK

If another “DTC CONFIRMATION PROCEDURE” occurs just before, turn ignition switch OFF and wait for at least 10 seconds, then perform the next test.

>> GO TO 2.

2.CHECK DTC DETECTION

  1. Start the engine
  2. Drive the vehicle.
  3. Maintain the following conditions for 10 seconds or more.

Selector lever : “L” POSITION

Accelerator pedal position : 0.7/8 or more

Vehicle speed : 10 km/h (6 MPH) or more

  1. Stop the vehicle.
  2. Check the first trip DTC.

Is “P285A” detected? YES >> Go to TM-233, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK INTERMITTENT INCIDENT

Refer to GI-39, "Intermittent Incident".

Is the inspection result normal? YES >> Replace the transaxle assembly. Refer to TM-283, "Removal and Installation".

NO >> Repair or replace malfunctioning parts.

P2859 Clutch A Pressure
DTC Logic DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition Possible causes P2859 CLUTCH A PRESSURE (Clutch A Pressu ...

Main power supply and ground circuit
Diagnosis Procedure 1.CHECK TCM POWER CIRCUIT (PART 1) Turn ignition switch OFF. Disconnect TCM connector. Check voltage between TCM harness connector terminals and ground. Is the insp ...

Other materials:

Symptom diagnosis
Audio system Symptom table Related to audio Related to hands-free phone Before performing diagnosis, confirm that the cellular phone being used by the customer is compatible with the vehicle. It is possible that a malfunction is occurring due to a version change of the phone ...

Precaution
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injur ...

Oil seal
Valve oil seal : Removal and Installation REMOVAL Rotate crankshaft, and set piston whose valve oil seal is to be removed to TDC. This will prevent valve from dropping into cylinder. CAUTION: When rotating crankshaft, be careful to avoid scarring front cover with timing chain. Re ...

© 2014-2026 Copyright www.nisentra.com