Nissan Sentra Service Manual: P2858 Clutch B Pressure

Nissan Sentra Service Manual / Transmission & driveline / Transaxle & transmission / CVT: RE0F11A / P2858 Clutch B Pressure

DTC Logic

DTC

CONSULT screen terms (Trouble diagnosis content)

DTC detection condition

Possible causes

P2858

CLUTCH B PRESSURE (Clutch B Pressure Engagement Performance)

The auxiliary gearbox gear ratio is 2.232 or more for the auxiliary gearbox 2GR ratio continuously for 5 seconds or more under the following diagnosis conditions:

Diagnosis conditions

Selector lever: Other than вЂњPвЂќ, вЂњRвЂќ and вЂњNвЂќ positions
Accelerator pedal position: 0.7/8 or more
Engine speed: More than 550 rpm
Output speed: More than 300 rpm
Secondary pulley speed: More than 300 rpm
Command for the 2GR of auxiliary gearbox is in progress.
Auxiliary gearbox shifting is not in progress.
TCM power supply voltage: More than 11 V

High clutch & reverse brake solenoid valve
Control valve assembly

DTC CONFIRMATION PROCEDURE

CAUTION:

Be sure to perform вЂњTM-228, "Diagnosis Procedure"вЂќ and then perform вЂњDTC CONFIRMATION PROCEDUREвЂќ.
Never perform вЂњDTC CONFIRMATION PROCEDUREвЂќ before the repairs. Doing so may result in a secondary malfunction.
Be careful of the driving speed.

1.PREPARATION BEFORE WORK

If another вЂњDTC CONFIRMATION PROCEDUREвЂќ occurs just before, turn ignition switch OFF and wait for at least 10 seconds, then perform the next test.

>> GO TO 2.

2.CHECK DTC DETECTION

Start the engine.
Drive the vehicle.
Maintain the following conditions for 10 seconds or more.

Selector lever : вЂњDвЂќ POSITION

Accelerator pedal position : 0.7/8 or more

Vehicle speed : 45 km/h (28 MPH) or more

Stop the vehicle
Check the first trip DTC.

Is вЂњP2858вЂќ detected? YES >> Go to TM-228, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK INTERMITTENT INCIDENT

Refer to GI-39, "Intermittent Incident".

Is the inspection result normal? YES >> Replace the transaxle assembly. Refer to TM-283, "Removal and Installation".

NO >> Repair or replace malfunctioning parts.

P2857 Clutch A Pressure

DTC Logic DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition Possible causes P2857 CLUTCH A PRESSURE (Clutch A Pressu ...

P2859 Clutch A Pressure

DTC Logic DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition Possible causes P2859 CLUTCH A PRESSURE (Clutch A Pressu ...

Other materials:

Heated seats (if so equipped)
The front seats are warmed by built-in heaters. Start the engine. Push the LO or HI position of the switch, as desired. The indicator light in the switch will illuminate. The heater is controlled by a thermostat, automatically turning the heater on and off. The indicator light ...

P1652 Starter motor system comm
Description ECM controls ON/OFF state of the starter relay, according to the engine and vehicle condition. ECM transmits a control signal to IPDM E/R via BCM by CAN communication. Under normal conditions, ECM controls and maintains the starter relay in OFF state during following condition: ...

Moonroof switch
Removal and installation REMOVAL Remove the map lamp. Refer to INL-52, "Removal and Installation". Release the pawls and remove the moonroof switch finisher (1). : Pawl Release the pawls and remove the moonroof switch (2). : Pawl INSTALLATION Installation is in the ...