Nissan Sentra manuals

Nissan Sentra Service Manual: P2014, P2016, P2017, P2018 Intake manifold runner control valve position sensor

Nissan Sentra Service Manual / Engine / Engine control system / Dtc/circuit diagnosis / P2014, P2016, P2017, P2018 Intake manifold runner control valve position sensor

DTC Logic

DTC DETECTION LOGIC

NOTE:

If DTC P2014, P2016, P2017 or P2018 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643. Refer to EC-353, "DTC Logic".

DTC No.

 CONSULT screen terms (Trouble diagnosis content)

 DTC detecting condition

 Possible cause
P2014 IN/MANIFOLD RUNNER POS SEN B1 (Intake manifold runner position sensor/ switch circuit bank 1) An excessively low voltage from the sensor is sent to ECM.
  • Harness or connectors (Intake manifold runner control position sensor circuit is shorted.)
  • Intake manifold runner control position sensor
  • Sensor power supply 2 circuit
P2016 IN/MANIFOLD RUNNER POS SEN B1 (Intake manifold runner position sensor/ switch circuit low bank 1)
P2017 IN/MANIFOLD RUNNER POS SEN B1 (Intake manifold runner position sensor/ switch circuit high bank 1) An excessively high voltage from the sensor is sent to ECM.
P2018 IN/MANIFOLD RUNNER POS SEN B1 (Intake manifold runner position sensor/ switch circuit intermittent bank 1)

DTC CONFIRMATION PROCEDURE

1.PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.
  2. Turn ignition switch ON.
  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm that battery voltage is more than 11 V at idle.

>> GO TO 2.

2.PERFORM DTC CONFIRMATION PROCEDURE

  1. Start engine and let it idle for 10 seconds.
  2. Check 1st trip DTC.

Is 1st trip DTC detected? YES >> Proceed to EC-416, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK INTAKE MANIFOLD RUNNER CONTROL VALVE POSITION SENSOR POWER SUPPLY

  1. Turn ignition switch OFF.
  2. Disconnect intake valve manifold runner control valve position sensor harness connector.
  3. Turn ignition switch ON.
  4. Check the voltage between intake valve manifold runner control valve position sensor harness connector.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 6.

NO >> GO TO 2.

2.CHECK INTAKE MANIFOLD RUNNER CONTROL VALVE POSITION SENSOR POWER SUPPLY CIRCUIT

Check the voltage between intake valve manifold runner control valve position sensor harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 4.

NO >> GO TO 3.

3.CHECK SENSOR POWER SUPPLY 2 CIRCUIT

Check sensor power supply 2 circuit. Refer to EC-444, "Diagnosis Procedure".

Is inspection result normal? YES >> Perform the trouble diagnosis for power supply circuit.

NO >> Repair or replace error-detected parts.

4.CHECK ECM GROUND CIRCUIT

  1. Turn ignition switch OFF.
  2. Disconnect ECM harness connector.
  3. Check the continuity between ECM harness connector and ground.


  1. Also check harness for short to power.

Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-39, "Intermittent Incident".

NO >> Repair or replace error-detected parts.

5.CHECK INTAKE MANIFOLD RUNNER CONTROL VALVE POSITION SENSOR GROUND CIRCUIT

  1. Turn ignition switch OFF.
  2. Disconnect ECM harness connector.
  3. Check the continuity between intake manifold runner control valve position sensor harness connector and ECM harness connector.


  1. Also check harness for short to power.

Is the inspection result normal? YES >> GO TO 6.

NO >> Repair or replace error-detected parts.

6.CHECK INTAKE MANIFOLD RUNNER CONTROL VALVE POSITION SENSOR INPUT SIGNAL CIRCUIT

  1. Check the continuity between intake manifold runner control valve position sensor harness connector and ECM harness connector.


  1. Also check harness for short to ground and to power.

Is the inspection result normal? YES >> GO TO 7.

NO >> Repair or replace error-detected parts.

7.CHECK INTERMITTENT INCIDENT

Perform GI-39, "Intermittent Incident".

Is the inspection result normal? YES >> Replace intake manifold assembly. Refer to EM-27, "Exploded View".

NO >> Repair or replace error-detected parts.

P2004 Intake manifold runner control valve
DTC Logic DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition Possible cause P2004 TUMBLE CONT/V (Intake manifold r ...

P2096, P2097 A/F Sensor 1
DTC Logic DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition Possible Cause P2096 POST CAT FUEL TRIM SYS B1 (Post ...

Other materials:

Component parts
Engine control system ENGINE CONTROL SYSTEM :Component Parts Location Engine room compartment No. Component Function 1 IPDM E/R IPDM E/R control the internal relays and the actuators. When CAN communication with ECM is impossible, IPDM E/R performs fail-sa ...

Increasing fuel economy
Keep your engine tuned up. Follow the recommended scheduled maintenance. Keep the tires inflated to the correct pressure. Low tire pressure increases tire wear and lowers fuel economy. Keep the wheels in correct alignment. Improper alignment increases tire wear and lowers fuel eco ...

Brake pedal position switch
Component Function Check 1.CHECK BRAKE PEDAL POSITION SWITCH FUNCTION With CONSULT Turn ignition switch ON. Select “ENGINE” using CONSULT. Select “BRAKE SW1” in “DATA MONITOR” mode. Check “BRAKE SW1” indication under the following conditions. ...

© 2014-2026 Copyright www.nisentra.com