Nissan Sentra manuals

Nissan Sentra Service Manual: P1800 Intake manifold tuning valve

Nissan Sentra Service Manual / Engine / Engine control system / Dtc/circuit diagnosis / P1800 Intake manifold tuning valve

DTC Logic

DTC DETECTION LOGIC

DTC No.

 CONSULT screen terms (Trouble diagnosis content)

 DTC detecting condition

 Possible cause
P1800 VIAS S/V-1 (Variable intake air system control solenoid valve-1) An excessively low or high voltage signal is sent to ECM through the intake manifold tuning valve.
  • Harness or connectors (The solenoid valve 1 circuit is open or shorted.)
  • Intake manifold tuning valve

DTC CONFIRMATION PROCEDURE

1.CONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.
  2. Turn ignition switch ON.
  3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:

Before performing the following procedure, confirm battery voltage is more than 11 V at idle.

>> GO TO 2.

2.PERFORM DTC CONFIRMATION PROCEDURE

  1. Start engine and warm it up to the normal operating temperature. [more than 60В°C (140В°F)]
  2. Let it idle for at least 10 seconds. (engine speed: less than 1,000 rpm)
  3. Check 1st trip DTC.

Is 1st trip DTC detected? YES >> Proceed to EC-408, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK INTAKE MANIFOLD TUNING VALVE MOTOR POWER SUPPLY

  1. Turn ignition switch ON.
  2. Check the voltage between ECM harness connector.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 3.

NO >> GO TO 2.

2.CHECK INTAKE MANIFOLD TUNING VALVE MOTOR POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF.
  2. Disconnect ECM harness connector.
  3. Disconnect IPDM E/R harness connector.
  4. Check the continuity between ECM harness connector and IPDM E/R harness connector.


  1. Also check harness for short to ground.

Is the inspection result normal? YES >> Perform the trouble diagnosis for power supply circuit.

NO >> Repair or replace error-detected parts.

3.CHECK INTAKE MANIFOLD TUNING VALVE MOTOR OUTPUT SIGNAL CIRCUIT

  1. Disconnect intake manifold tuning valve motor harness connector
  2. Check the continuity between intake manifold tuning valve motor harness connector and ECM harness connector.


  1. Also check harness for short to ground and to power.

Is the inspection result normal? YES >> GO TO 4.

NO >> Repair or replace error-detected parts.

4.CHECK INTAKE MANIFOLD TUNING VALVE MOTOR

Check the intake manifold tuning valve motor. Refer to EC-409, "Component Inspection (Intake Manifold Tuning Valve)".

Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-39, "Intermittent Incident".

NO >> Replace intake manifold assembly. Refer to EM-27, "Removal and Installation".

Component Inspection (Intake Manifold Tuning Valve)

1.CHECK INTAKE MANIFOLD TUNING VALVE MOTOR

  1. Turn ignition switch OFF.
  2. Disconnect intake manifold tuning valve motor harness connector.
  3. Check the resistance between intake manifold tuning valve motor terminals as per the following.

Is the inspection result normal?


Is the inspection result normal? YES >> INSPECTION END

NO >> Replace intake manifold. Refer to EM-27, "Removal and Installation".

P1715 Input speed sensor
Description ECM receives input speed sensor signal from TCM through CAN communication line. ECM uses this signal for engine control. DTC Logic DTC DETECTION LOGIC NOTE: If DTC P1715 is disp ...

P1805 Brake switch
DTC Logic DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition Possible cause P1805 BRAKE SW/CIRCUIT (Brake switch c ...

Other materials:

Fuel level sensor signal circuit
Description The fuel level sensor unit and fuel pump detects the approximate fuel level in the fuel tank and transmits the fuel level signal to the combination meter. Component function check 1.Combination meter input signal Select meter/m&a on consult. Using FUEL METER of DATA MONI ...

Rear drum brake
Brake Burnishing CAUTION: Burnish contact surfaces between brake drum and brake lining according to the following procedure after refinishing or replacing brake drum, or if a soft pedal occurs at very low mileage. Be careful of vehicle speed because the brake does not operate firml ...

System
System Diagram FRONT POWER WINDOW LH ANTI-PINCH SYSTEM System Description MAIN POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH INPUT/OUTPUT SIGNAL CHART Item Input signal to main power window and door lock/unlock switch Main power window and door lock/unlock switch function A ...

© 2014-2024 Copyright www.nisentra.com