Description
ECM controls ON/OFF state of the starter relay, according to the engine and vehicle condition. ECM transmits a control signal to IPDM E/R via BCM by CAN communication.
Under normal conditions, ECM controls and maintains the starter relay in OFF state during following condition:
When detecting a decrease in engine speed due to rapid deceleration or heavy load condition, ECM controls and reactivates the starter relay.
IPDM E/R detects a control state of starter relay and starter control relay and transmits a feedback signal to ECM via CAN communication.
DTC Logic
DTC DETECTION LOGIC
NOTE:
DTC No. | CONSULT screen terms (Trouble diagnosis content) | DTC detecting condition | Possible cause | |
P1650 | STR MTR RELAY 2 (Starter motor relay 2) | A | Starter relay is stuck ON. |
|
B | Starter relay power supply circuit is excessively high voltage. |
|
||
C | Starter relay circuit is excessively low voltage |
|
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION A AND C
Is 1st trip DTC detected? YES >> Proceed to EC-400, "Diagnosis Procedure".
NO >> GO TO 3.
3.PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION B
With CONSULT
CAUTION:
Always drive at a safe speed.
Without CONSULT
CAUTION:
Always drive at a safe speed.
For M/T models: Fully release the clutch pedal.
Is 1st trip DTC detected? YES >> Proceed to EC-400, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis Procedure
1.CHECK SELF-DIAGNOSTIC RESULT IN BCM
With CONSULT
Check self-diagnostic result in BCM.
Are any DTC detected? YES >> Check the DTC. Refer to PCS-20, "DTC Index" (with intelligent key), PCS-48, "DTC Index" (without intelligent key).
NO >> GO TO 2.
2.CHECK SELF-DIAGNOSTIC RESULT IN IPDM E/R
With CONSULT
Check self-diagnostic result in IPDM E/R.
Are any DTC detected? YES >> Check the DTC. Refer to BCS-49, "DTC Index" (with intelligent key), BCS-109, "DTC Index" (without intelligent key).
NO >> GO TO 3.
3.CHECK STARTER RELAY POWER SUPPLY CIRCUIT
Check the starter motor relay power supply circuit. Refer to PCS-29, "Diagnosis Procedure" (with intelligent key), or PCS-57, "Diagnosis Procedure" (without intelligent key).
Is the inspection result normal? YES >> GO TO 4.
NO >> Repair or replace error-detected parts.
4.CHECK STARTER RELAY CONTROL SIGNAL CIRCUIT
Is the inspection result normal? YES >> GO TO 5.
NO >> Repair or replace error-detected parts.
5.CHECK INTERMITTENT INCIDENT
Check intermittent incident. Refer to GI-39, "Intermittent Incident".
Is the inspection result normal? YES >> Replace IPDM E/R. Refer to PCS-30, "Removal and Installation".
NO >> Repair or replace error-detected parts.
Unbalance steering wheel turning force and return between right
and left
Description
Unbalance steering wheel turning force and return between right
and left.
Diagnosis Procedure
1.CHECK THE ILLUMINATION OF THE EPS WARNING LAMP
Check the EPS warning lamp while engine is running.
Does the EPS warning lamp turn OFF?
YES >> GO TO 2.
NO >> Refer to S ...
B0010, B0011 Passenger airbag module
Description
DTC B0010, B0011 PASSENGER AIR BAG MODULE
The passenger air bag module is dual stage and is wired to the air bag
diagnosis sensor unit. The air bag diagnosis
sensor unit will monitor for opens and shorts in detected lines to the passenger
air bag module.
PART LOCATION
Refer to S ...
How to Follow Test Groups in Trouble Diagnosis
Test group number and test group title
Test group number and test group title are shown in the upper portion of
each test group.
Work and diagnosis procedure
Start to diagnose a problem using procedures indicated in enclosed test
groups.
Questions and results
...