Nissan Sentra Service Manual: P0715 Input speed sensor A

Nissan Sentra Service Manual / Transmission & driveline / Transaxle & transmission / CVT: RE0F11A / P0715 Input speed sensor A

DTC Logic

DTC DETECTION LOGIC

DTC

CONSULT screen terms (Trouble diagnosis content)

DTC detection condition

Possible causes

P0715

INPUT SPEED SENSOR A (Input/Turbine Speed Sensor A Circuit)

The primary speed sensor value is less than 150 rpm continuously for 5 seconds or more under the following diagnosis conditions:

Diagnosis conditions

Secondary pulley speed: 1,000 rpm or more
TCM power supply voltage: More than 11 V

Harness or connector (Primary speed sensor circuit is open or shorted)
Primary speed sensor

The primary speed sensor value is 240 rpm or less continuously for 500 msec or more under the following diagnosis conditions:

Diagnosis conditions

10-msec-ago primary pulley speed: 1,000 rpm or more
TCM power supply voltage: More than 11 V

DTC CONFIRMATION PROCEDURE

CAUTION:

Be careful of the driving speed.

1.PREPARATION BEFORE WORK

If another вЂњDTC CONFIRMATION PROCEDUREвЂќ occurs just before, turn ignition switch OFF and wait for at least 10 seconds, then perform the next test.

>> GO TO 2.

2.CHECK DTC DETECTION

Start the engine.
Drive the vehicle.
Maintain the following conditions for 10 seconds or more.

Selector lever : вЂњLвЂќ POSITION

Vehicle speed : 40 km/h (25 MPH) or more

Stop the vehicle.
Check the first trip DTC.

Is вЂњP0715вЂќ detected? YES >> Go to TM-178, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK PRIMARY SPEED SENSOR POWER CIRCUIT

Turn ignition switch OFF.
Disconnect primary speed sensor connector.
Turn ignition switch ON.
Check voltage between primary speed sensor harness connector terminal and ground.

Is the check result normal?

Is the check result normal? YES >> GO TO 2.

NO >> GO TO 6.

2.CHECK PRIMARY SPEED SENSOR GROUND CIRCUIT

Check continuity between primary speed sensor harness connector terminal and ground.

Is the check result normal?

Is the check result normal? YES >> GO TO 3.

NO >> Repair or replace malfunctioning parts

3.CHECK CIRCUIT BETWEEN PRIMARY SPEED SENSOR AND TCM (PART 1)

Turn ignition switch OFF.
Disconnect TCM connector.
Check continuity between primary speed sensor harness connector terminal and TCM harness connector terminal.

Is the check result normal?

Is the check result normal? YES >> GO TO 4.

NO >> Repair or replace malfunctioning parts.

4.CHECK CIRCUIT BETWEEN PRIMARY SPEED SENSOR AND TCM (PART 2)

Check continuity between primary speed sensor harness connector terminal and ground.

Is the check result normal?

Is the check result normal? YES >> GO TO 5.

NO >> Repair or replace malfunctioning parts.

5.Check TCM Input signals

Connect all of disconnected connectors.
Lift the vehicle.
Start the engine.
Check frequency of primary speed sensor.

Is the check result normal?

Is the check result normal? YES >> Check intermittent incident. Refer to GI-39, "Intermittent Incident".

NO >> Replace primary speed sensor. Refer to TM-268, "Removal and Installation".

6.DETECT MALFUNCTIONING ITEMS

Check the following items:

Harness open circuit or short circuit between the ignition switch and IPDM E/R. Refer to PG-20, "Wiring Diagram вЂ” Ignition Power Supply вЂ”".
Harness open circuit or short circuit between IPDM E/R and primary speed sensor.
10A fuse (No.45, IPDM E/R). Refer to PG-49, "IPDM E/R Terminal Arrangement".
IPDM E/R

Is the check result normal? YES >> Check intermittent incident. Refer to GI-39, "Intermittent Incident".

NO >> Repair or replace malfunctioning parts.

P0713 Transmission fluid temperature sensor A

DTC Logic DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition Possible causes P0713 FLUID TEMP SENSOR A (Transmission ...

P0720 Output speed sensor

DTC Logic DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition Possible causes P0720 OUTPUT SPEED SENSOR (Output Speed ...

Other materials:

Front fog lamp
Removal and Installation FOG LAMP Removal Position the fender protector aside. Refer to EXT-28, "FENDER PROTECTOR : Removal and Installation - Front Fender Protector". Disconnect the harness connector from the front fog lamp. Remove the screws and the front fog lamp. Inst ...

P0011 IVT control
DTC Logic DTC DETECTION LOGIC NOTE: If DTC P0011 is displayed with DTC P0075, first perform the trouble diagnosis for EC-180, "DTC Logic". DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition Possible cause P0011 INT/V TIM CO ...

Adjusting the set speed - Dynamic radar cruise control with full-speed range
Adjusting the set speed by the switch To change the set speed, press the "+ RES" or "- SET" switch until the desired set speed is displayed. Increases the speed (Except when the vehicle has been stopped by system control in vehicle- to-vehicle distance control mode) Decreases th ...