Nissan Sentra manuals

Nissan Sentra Service Manual: P0520 EOP  System

Nissan Sentra Service Manual / Engine / Engine control system / Dtc/circuit diagnosis / P0520 EOP  System

DTC Logic

DTC DETECTION LOGIC

DTC No.

 CONSULT screen terms (Trouble diagnosis content)

 DTC detecting condition

 Possible cause
P0520 EOP SENSOR/SWITCH (Engine oil pressure sensor/ switch circuit) ECM detects the following status continuously for 5 seconds or more:
  • A voltage signal transmitted from the engine oil pressure sensor is lower than 0.3 V.
  • A voltage signal transmitted from the engine oil pressure sensor is higher than 5.02 V.
  • Harness or connectors (EOP sensor circuit is open or shorted)
  • EOP sensor
  • Sensor power supply 2 circuit

DTC CONFIRMATION PROCEDURE

1.PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

>> GO TO 2.

2.CHECK ENGINE OIL LEVEL

  1. Turn ignition switch OFF.
  2. Check engine oil level. Refer to LU-7, "Inspection".

Is inspection result normal? YES >> GO TO 3.

NO >> Check engine oil leak. Refer to LU-6, "Engine Lubrication System Schematic".

3.PERFORM DTC CONFIRMATION PROCEDURE

  1. Start engine and let it idle for at least 5 seconds.
  2. Check 1st trip DTC.

Is 1st trip DTC detected? YES >> Proceed to EC-340, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK EOP SENSOR POWER SUPPLY CIRCUIT-1

  1. Turn ignition switch OFF.
  2. Disconnect EOP sensor harness connector.
  3. Turn ignition switch ON.
  4. Check the voltage between EOP sensor harness connector terminals.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 2.

NO >> GO TO 4.

2.CHECK EOP SENSOR SIGNAL CIRCUIT

  1. Turn ignition switch OFF
  2. Disconnect ECM harness connectors.
  3. Check the continuity between EOP sensor harness connector and ECM harness connector.


  1. Also check harness for short to ground and short to power.

Is the inspection result normal? YES >> GO TO 3.

NO >> Repair or replace error-detected parts.

3.CHECK EOP SENSOR

Check EOP sensor. Refer to EC-342, "Component Inspection (EOP Sensor)".

Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-39, "Intermittent Incident".

NO >> Replace EOP sensor. Refer to EM-94, "Exploded View".

4.CHECK EOP SENSOR POWER SUPPLY CIRCUIT-2

Check the voltage between EOP sensor harness connector terminal and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 6.

NO >> GO TO 5.

5.CHECK SENSOR POWER SUPPLY 2 CIRCUIT

Check sensor power supply 2 circuit. Refer to EC-444, "Diagnosis Procedure".

Is inspection result normal? YES >> Perform the trouble diagnosis for power supply circuit.

NO >> Repair or replace error-detected parts.

6.CHECK EOP SENSOR GROUND CIRCUIT

  1. Turn ignition switch OFF.
  2. Disconnect ECM harness connector.
  3. Check the continuity between EOP sensor harness connector and ECM harness connector.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 7.

NO >> Repair or replace error-detected parts.

7.CHECK ECM GROUND CIRCUIT

Check the continuity between ECM harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-39, "Intermittent Incident".

NO >> Repair or replace error-detected parts.

Component Inspection (EOP Sensor)

1.CHECK EOP SENSOR

  1. Turn ignition switch OFF.
  2. Disconnect EOP sensor harness connector.
  3. Check the resistance between EOP sensor connector terminals.

Is the inspection result normal?


Is the inspection result normal? YES >> INSPECTION END

NO >> Replace EOP sensor. Refer to EM-94, "Exploded View".

P050A, P050B, P050E Cold start control
Description ECM controls ignition timing and engine idle speed when engine is started with pre-warming up condition. This control promotes the activation of three way catalyst by heating the c ...

P0524 Engine oil pressure
DTC Logic DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition Possible cause P0524 ENGINE OIL PRESSURE (Engine oil ...

Other materials:

Headlamp (hi) circuit
Description The IPDM E/R (intelligent power distribution module engine room) controls the headlamp high relay based on inputs from the BCM over the CAN communication lines. When the headlamp high relay is energized, power flows through fuses 41 and 42, located in the IPDM E/R. Power then flo ...

C1609 Vehicle speed signal
DTC Logic Dtc detection logic DTC Display item Malfunction detected condition Possible cause C1609 CAN VHCL SPEED Malfunction is detected in vehicle speed signal that is output from abs actuator and electric unit (control unit) via can communication. ...

Adjustment of steering angle sensor neutral position
Description Refer to the table below to determine if adjustment of steering angle sensor neutral position is required. ×: Required –: Not required Work Procedure ADJUSTMENT OF STEERING ANGLE SENSOR NEUTRAL POSITION CAUTION: To adjust neutral position of steering angle sensor, ...

© 2014-2025 Copyright www.nisentra.com