Nissan Sentra manuals

Nissan Sentra Service Manual: P0117, P0118 ECT Sensor

Nissan Sentra Service Manual / Engine / Engine control system / Dtc/circuit diagnosis / P0117, P0118 ECT Sensor

DTC Logic

DTC DETECTION LOGIC

DTC No.

 CONSULT screen terms (Trouble diagnosis content)

 DTC detecting condition

 Possible cause
P0117 ECT SEN/CIRC (Engine coolant temperature sensor 1 circuit low) An excessively low voltage from the engine coolant temperature sensor is sent to ECM.
  • Harness or connectors (Engine coolant temperature sensor circuit is open or shorted.)
  • Engine coolant temperature sensor
P0118 ECT SEN/CIRC (Engine coolant temperature sensor 1 circuit high) An excessively high voltage from the engine coolant temperature sensor is sent to ECM.

DTC CONFIRMATION PROCEDURE

1.PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

  1. Turn ignition switch OFF and wait at least 10 seconds.
  2. Turn ignition switch ON.
  3. Turn ignition switch OFF and wait at least 10 seconds.

>> GO TO 2.

2.PERFORM DTC CONFIRMATION PROCEDURE

  1. Turn ignition switch ON and wait at least 5 seconds.
  2. Check DTC.

Is DTC detected? YES >> Proceed to EC-198, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK ENGINE COOLANT TEMPERATURE SENSOR POWER SUPPLY

  1. Turn ignition switch OFF.
  2. Disconnect engine coolant temperature (ECT) sensor harness connector.
  3. Turn ignition switch ON.
  4. Check the voltage between ECT sensor harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 3.

NO >> GO TO 2.

2.CHECK ENGINE COOLANT TEMPERATURE SENSOR POWER SUPPLY CIRCUIT

  1. Turn ignition switch OFF.
  2. Disconnect ECM harness connector.
  3. Check the continuity between ECT sensor harness connector and ECM harness connector.


  1. Also check harness for short to ground.

Is the inspection result normal? YES >> Perform the trouble diagnosis for power supply circuit.

NO >> Repair or replace error-detected parts.

3.CHECK ENGINE COOLANT TEMPERATURE SENSOR GROUND CIRCUIT

  1. Turn ignition switch OFF.
  2. Disconnect ECM harness connector.
  3. Check the continuity between ECT sensor harness connector and ECM harness connector.


  1. Also check harness for short to ground to power.

Is the inspection result normal? YES >> GO TO 4.

NO >> Repair or replace error-detected parts.

4.CHECK ENGINE COOLANT TEMPERATURE SENSOR

Check the engine coolant temperature sensor. Refer to EC-199, "Component Inspection (ECT Sensor)".

Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-39, "Intermittent Incident".

NO >> Replace engine coolant temperature sensor. Refer to CO-24, "Exploded View".

Component Inspection (ECT Sensor)

1.CHECK ENGINE COOLANT TEMPERATURE SENSOR

  1. Turn ignition switch OFF.
  2. Disconnect engine coolant temperature sensor harness connector.
  3. Remove engine coolant temperature sensor.
  4. Check resistance between engine coolant temperature sensor terminals by heating with hot water as shown in the figure.


Is the inspection result normal?


Is the inspection result normal? YES >> INSPECTION END

NO >> Replace engine coolant temperature sensor. Refer to CO-24, "Exploded View".

P0116 ECT Sensor
DTC Logic DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition Possible cause P0116 ECT SEN/CIRC (Engine coolant tem ...

P0122, P0123 TP Sensor
DTC Logic DTC DETECTION LOGIC NOTE: If DTC P0122 or P0123 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643. Refer to EC-353, "DTC Logic". DTC No ...

Other materials:

Precaution for supplemental restraint system (srs) "air bag" and "seat belt pre-tensioner"
The supplemental restraint system such as “air bag” and “seat belt pre-tensioner”, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain types of collision. Information necessary to service the system ...

Engine assembly M/T
M/T : Exploded View Washer Upper torque rod (RH) Engine mounting insulator (RH) Rear torque rod bracket Rear torque rod Engine mounting bracket (LH) Engine mounting frame support (LH) Engine mounting insulator (LH) CAUTION: Check that the stud bolt (*2) is tight at the spe ...

On Board Diagnostic (OBD) System of Engine and CVT
The ECM has an on board diagnostic system. It will light up the malfunction indicator lamp (MIL) to warn the driver of a malfunction causing emission deterioration. CAUTION: Be sure to turn the ignition switch OFF and disconnect the negative battery cable before any repair or inspection ...

© 2014-2024 Copyright www.nisentra.com