Nissan Sentra manuals

Nissan Sentra Service Manual: Overdrive control switch

Nissan Sentra Service Manual / Transmission & driveline / Transaxle & transmission / CVT: RE0F11A / Overdrive control switch

Component Function Check

1.CHECK SPORT INDICATOR LAMP FUNCTION

Check OD OFF indicator lamp turns ON for approx. 2 seconds when ignition switch turns ON.

Is the inspection result normal? YES >> GO TO 2.

NO >> Go to TM-239, "Diagnosis Procedure".

2.CHECK SPORT MODE SWITCH FUNCTION

  1. Shift the selector lever to “D” position.
  2. Check that OD OFF indicator lamp turns ON/OFF when overdrive control switch is operated.

Is the inspection result normal? YES >> INSPECTION END

NO >> Go to TM-236, "Diagnosis Procedure".

Diagnosis Procedure

1.CHECK OVERDRIVE CONTROL SWITCH CIRCUIT

  1. Turn ignition switch OFF
  2. Disconnect CVT shift selector connector.
  3. Turn ignition switch ON.
  4. Check voltage between CVT shift selector harness connector terminals.

result normal?Is the inspection
result normal?

YES >> GO TO 2.

NO >> GO TO 4.

2.CHECK CVT SHIFT SELECTOR ASSEMBLY

Check continuity between CVT shift selector connector terminals.

result normal? Is the inspection
result normal?

YES >> Check intermittent incident. Refer to GI-39, "Intermittent Incident".

NO >> GO TO 3.

3.CHECK OVERDRIVE CONTROL SWITCH

Check overdrive control switch. Refer to TM-237, "Component Inspection (Overdrive Control Switch)".

Is the inspection result normal? YES >> Replace CVT shift selector assembly. Refer to TM-253, "Removal and Installation".

NO >> Repair or replace malfunctioning parts.

4.CHECK GROUND CIRCUIT

Check continuity between CVT shift selector harness connector terminal and ground.

result normal? Is the inspection
result normal?

YES >> GO TO 5.

NO >> Repair or replace malfunctioning parts.

5.CHECK CIRCUIT BETWEEN COMBINATION METER AND CVT SHIFT SELECTOR (PART 1)

  1. Turn ignition switch OFF
  2. Disconnect combination meter connector.
  3. Check continuity between combination meter harness connector terminal and CVT shift selector harness connector terminal.

result normal? Is the inspection
result normal?

YES >> GO TO 6.

NO >> Repair or replace malfunctioning parts.

6.CHECK CIRCUIT BETWEEN COMBINATION METER AND CVT SHIFT SELECTOR (PART 2)

Check continuity between combination meter harness connector terminal and ground.

result normal? Is the inspection
result normal?

YES >> GO TO 7.

NO >> Repair or replace malfunctioning parts.

7.CHECK COMBINATION METER INPUT SIGNAL

  1. Connect all of disconnected connectors.
  2. Turn ignition switch ON.
  3. Select “Data Monitor” in “METER/M&A”.
  4. Select “O/D OFF SW”.
  5. Check that “O/D OFF SW” turns ON/OFF when overdrive control switch is operated. Refer to MWI-20, "Reference Value".

Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-39, "Intermittent Incident".

NO >> Replace combination meter. Refer to MWI-77, "Removal and Installation".

Component Inspection (Overdrive Control Switch)

1.Check overdrive control switch

Check continuity between wires of selector lever knob 1.

Is the inspection


result normal?Is the inspection
result normal?

YES >> INSPECTION END

NO >> Replace selector lever knob. Refer to TM-253, "Removal and Installation".

Main power supply and ground circuit
Diagnosis Procedure 1.CHECK TCM POWER CIRCUIT (PART 1) Turn ignition switch OFF. Disconnect TCM connector. Check voltage between TCM harness connector terminals and ground. Is the insp ...

Od off indicator lamp
Component Function Check 1.CHECK OD OFF INDICATOR LAMP FUNCTION Check OD OFF indicator lamp turns ON for approx. 2 seconds when ignition switch turns ON. Is the inspection result normal? YES ...

Other materials:

Door lock and unlock switch
Component function check 1.Check function Select door lock of bcm using consult. Select cdl lock sw, cdl unlock sw in data monitor mode. Check that the function operates normally according to the following conditions. Is the inspection result normal? YES >> Main power windo ...

System
Headlamp system HEADLAMP SYSTEM : System Diagram HEADLAMP SYSTEM : System Description LOW BEAM OPERATION When the lighting switch is in 2nd position, the BCM receives input requesting the headlamps to illuminate. This input is communicated to the IPDM E/R across the CAN communication l ...

1144 Incomplete steering angle sensor adjustment
DTC Logic Dtc detection logic Dtc Display item Malfunction detected condition Possible causes C1144 St ang sen signal When neutral position adjustment of steering angle sensor is not complete. Harness or connector Steering angle sensor Abs actu ...

© 2014-2026 Copyright www.nisentra.com