Nissan Sentra manuals

Nissan Sentra Service Manual: Interior room lamp control circuit

Description

Controls each interior room lamp (ground side) by pwm signal.

Note:

Pwm signal control period is approximately 250 hz (in the gradual brightening/dimming).

Component function check

Caution:

Before performing the diagnosis, check that the following are normal.

1.Check interior room lamp control function

Consult active test


  1. Se the map lamp switch or room lamp switch to door.
  2. Turn ignition switch on.
  3. Select int lamp of bcm (int lamp) active test item.
  4. While operating the test items, check that each interior room lamp turns ON/OFF (gradual brightening/ dimming).

On : interior room lamp gradual brightening

Off : interior room lamp gradual dimming

Does the interior room lamp turns ON/OFF (gradual brightening/dimming)? YES >> Interior room lamp control circuit is normal.

NO >> Refer to INL-45, "Diagnosis Procedure".

Diagnosis procedure

Regarding Wiring Diagram information, refer to INL-17, "Wiring Diagram".

1.Check interior room lamp control output

Consult active test


  1. Turn ignition switch OFF
  2. Remove all the bulbs of room lamp and map lamp.
  3. Turn ignition switch on.
  4. Select int lamp of bcm (int lamp) active test item.
  5. While operating the test item, check continuity between BCM harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? Yes >> interior room lamp control circuit is operating normally.

Fixed on>>go to 3.

Fixed off>>go to 2.

2.Check interior room lamp control open circuit

  1. Turn ignition switch off.
  2. Disconnect bcm connector and room lamp and map lamp connector.
  3. Check continuity between BCM harness connector and room lamp harness connector.

Is the inspection result normal?


Is the inspection result normal? Yes >> check interior room lamps for an open. If ng, replace lamp in question. Refer to inl-55, "removal and installation" (room lamp) or inl-52, "removal and installation" (map lamp). If ok, replace bcm. Refer to bcs-73, "removal and installation" (with intelligent key), bcs-126, "removal and installation" (without intelligent key).

No >> repair or replace harness or connector.

3.Check interior room lamp control short to ground

  1. Turn ignition switch off.
  2. Disconnect BCM connector.
  3. Check continuity between BCM harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? Yes >> check interior room lamps for an internal short to ground. If ng, replace lamp in question. Refer to inl-55, "removal and installation" (room lamp) or inl-52, "removal and installation" (map lamp). If ok, replace bcm. Refer to bcs-73, "removal and installation" (with intelligent key), bcs-126, "removal and installation" (without intelligent key).

No >> repair or replace harness or connector.

Battery saver output/power supply circuit
Description Provides the battery saver output/power supply. Also cuts the power supply when the interior lamp battery saver is activated. Component function check 1.Check battery saver output/po ...

Trunk room lamp circuit
Description Controls the trunk room lamp (ground side) to turn the trunk room lamp on and off. Diagnosis Procedure Regarding wiring diagram information, refer to inl-17, "wiring diagram" ...

Other materials:

Steering wheel turning force is heavy or light
Description Steering wheel turning force is heavy or light. Diagnosis Procedure 1.PERFORM SELF-DIAGNOSIS With CONSULT Turn the ignition switch OFF to ON. Perform EPS self-diagnosis. Is any DTC detected? YES >> Check the DTC. Refer to STC-14, "DTC Index". NO & ...

Basic inspection
Inspection and adjustment Additional service when replacing control unit (bcm) Additional service when replacing control unit (bcm) : description Before replacement When replacing BCM, save or print current vehicle specification with CONSULT configuration before replacement. Note: If “ ...

B2267 engine speed
Description The engine speed signal is transmitted from ecm to the combination meter via can communication. Dtc logic Dtc detection logic Dtc Consult Detection condition Possible malfunction location B2267 Tacho meter [b2267] ECM continuously transmits abnorma ...

© 2014-2024 Copyright www.nisentra.com