Nissan Sentra Service Manual: Headlining
Exploded View
STANDARD ROOF
- Headlining
- Assist grip
- Map lamp bracket
- Sun visor (RH)
- Sun visor cover
- Sun visor holder
- Map lamp
- Sun visor (LH)
- Interior room lamp
- Assist grip cap
- Headlining clip
- Metal clip
Pawl
Metal clip
Sunroof
- Headlining
- Assist grip
- Sunroof welt
- Dual lock fastener
- Map lamp bracket
- Sun visor (RH)
- Sun visor cover
- Sun visor holder
- Map lamp
- Sun visor (LH)
- Interior room lamp
- Assist grip cap
- Headlining clip
- Metal clip
Pawl
Metal clip
Removal and Installation
REMOVAL
- Remove front pillar finishers (LH/RH). Refer to INT-24, "FRONT PILLAR
FINISHER : Removal and Installation".
- Remove front seat assemblies. Refer to the following.
- Refer to SE-18, "DRIVER SIDE : Removal and Installation - Seat Assembly"
(Driver Seat).
- Refer to SE-20, "PASSENGER SIDE : Removal and Installation - Seat
Assembly" (Passenger Seat).
- Remove center pillar upper finishers (LH/RH). Refer to INT-28, "CENTER
PILLAR UPPER FINISHER :
Removal and Installation".
- Remove rear seat back. Refer to SE-23, "Removal and Installation - 60:40
Split Seatback".
- Remove rear pillar finishers (LH/RH). Refer to INT-29, "REAR PILLAR
FINISHER : Removal and Installation".
- Remove center console assembly. Refer to IP-17, "Removal and
Installation".
- Remove shift selector assembly. Refer to TM-253, "Removal and
Installation".
- Remove all assist grips.
- Release pawl of assist grip cap (1) using a suitable tool (A).
Slide assist grip cap forward and remove as shown.
Pawl
- Slide assist grip (2) forward and remove.
- Remove metal clips from body panel.
- Remove room lamp. Refer to INL-55, "Removal and Installation".
- Remove map lamp. Refer to INL-52, "Removal and Installation".
- Remove sunroof welt (if equipped).
- Remove sun visor.
- Release sun visor cover pawls using a suitable tool (A), then
remove sun visor cover.
: Pawl
- Remove screws and the sun visors (LH/RH).
- Remove all sun visor holders.
Rotate 90В° and remove as shown.
- Remove headlining clips.
- Remove headlining from roof panel as shown. Adjust the position
of headlining so that it can be removed through passenger
side door.
- Remove headlining as shown.
CAUTION:
- Two people are required for removal in order to prevent
damage.
- Do not bend headlining when removing.
- Be careful not to scratch or damage any part of the body
while removing the headliner.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
- When installing headlining, start by installing both sun visor
holders and the headlining clips in
order to keep the headlining in position.
- Do not bend headlining when installing.
- Be careful that the surface is not wrinkled when installing.
- When installing assist grip, install metal clip (1) to assist grip
clip (2), then install to the body panel.
Exploded View
Floor trim
Harness protector
Front floor spacer (RH)
Front floor spacer (LH)
Rear floor spacer (LH)
Rear floor spacer (RH)
Column hole cover
Pawl
Front
Removal ...
Exploded View
Trunk floor trim
Trunk front floor spacer (LH)
Trunk side finisher (LH)
Reflector box assembly*
Trunk rear plate
Trunk side finisher (RH)
Trunk front floor spacer (RH ...
Other materials:
P0962 Pressure control solenoid A
DTC Logic
DTC DETECTION LOGIC
DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
Possible causes
P0962
PRESSURE CONTROL SOLENOID
A
(Pressure Control Solenoid A
Control Circuit Low)
The line pressure solenoid valve current is 200
...
Manual transmission (if so equipped)
The ignition switch includes a device that helps
prevent accidental removal of the key while driving.
The key can only be removed when the ignition
switch is in the LOCK position.
On manual transmission models, to turn the ignition
key to LOCK position from ACC or ON
position, turn the ...
Slide front armrest (if so equipped)
To adjust the front armrest, take the leather cover
and slide it to the front or rear.
...
© 2014-2024 Copyright www.nisentra.com