Nissan Sentra manuals

Nissan Sentra Service Manual: Fuel pump

Nissan Sentra Service Manual / Engine / Engine control system / Dtc/circuit diagnosis / Fuel pump

Component Function Check

1.CHECK FUEL PUMP FUNCTION

  1. Turn ignition switch ON.
  2. Pinch fuel feed hose two fingers. with
    two fingers.

Fuel pressure pulsation should be felt on the fuel feed


Fuel pressure pulsation should be felt on the fuel feed hose for 1 second after ignition switch is turned ON.

Is the inspection result normal? YES >> INSPECTION END

NO >> Proceed to EC-453, "Diagnosis Procedure".

Diagnosis Procedure

1.CHECK FUEL PUMP POWER SUPPLY CIRCUIT-1

  1. Turn ignition switch OFF.
  2. Disconnect ECM harness connector.
  3. Turn ignition switch ON.
  4. Check the voltage between ECM harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 3.

NO >> GO TO 2.

2.CHECK FUEL PUMP POWER SUPPLY CIRCUIT-2

  1. Turn ignition switch OFF.
  2. Disconnect IPDM E/R harness connector.
  3. Check the continuity between IPDM E/R harness connector and ECM harness connector.


  1. Also check harness for short to ground and short to power.

Is the inspection result normal? YES >> GO TO 8.

NO >> Repair or replace error-detected parts.

3.CHECK FUEL PUMP POWER SUPPLY CIRCUIT-3

  1. Turn ignition switch OFF.
  2. Reconnect all harness connectors disconnected.
  3. Disconnect fuel pump harness connector.
  4. Turn ignition switch ON.
  5. Check the voltage between fuel pump harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 6.

NO >> GO TO 4.

4.CHECK FUSE

  1. Turn ignition switch OFF.
  2. Disconnect 15A fuse (No. 50) from IPDM E/R.
  3. Check 15A fuse.

Is the inspection result normal? YES >> GO TO 5.

NO >> Replace 15A fuse.

5.CHECK FUEL PUMP POWER SUPPLY CIRCUIT-4

  1. Turn ignition switch OFF.
  2. Disconnect IPDM E/R harness connector
  3. Check the continuity between IPDM E/R harness connector and fuel pump harness connector.


  1. Also check harness for short to ground and short to power.

Is the inspection result normal? YES >> GO TO 6.

NO >> Repair or replace error-detected parts.

6.CHECK FUEL PUMP GROUND CIRCUIT

  1. Turn ignition switch OFF.
  2. Check the continuity between fuel pump harness connector and ground.


  1. Also check harness for short to power.

Is the inspection result normal? YES >> GO TO 7.

NO >> Repair or replace error-detected parts.

7.CHECK FUEL PUMP

Check fuel pump. Refer to EC-455, "Component Inspection (Fuel Pump)".

Is the inspection result normal? YES >> GO TO 8.

NO >> Replace fuel filter and fuel pump. Refer to FL-6, "Exploded View".

8.CHECK INTERMITTENT INCIDENT

Check intermittent incident. Refer to GI-39, "Intermittent Incident".

Is the inspection result normal? YES >> Replace IPDM E/R. Refer to PCS-30, "Removal and Installation" (With intelligent key) or PCS-58, "Removal and Installation" (Without intelligent key).

NO >> Repair or replace error-detected parts.

Component Inspection (Fuel Pump)

1.CHECK FUEL PUMP

  1. Turn ignition switch OFF
  2. Disconnect fuel level sensor unit and fuel pump harness connector.
  3. Check resistance between fuel pump terminals as follows.

Is the inspection result normal?


Is the inspection result normal? YES >> INSPECTION END

NO >> Replace fuel filter and fuel pump. Refer to FL-6, "Removal and Installation".

Fuel injector
Component Function Check 1.INSPECTION START Turn ignition switch to START. Is any cylinder ignited? YES >> GO TO 2. NO >> Proceed to EC-450, "Diagnosis Procedure". 2.CH ...

Ignition signal
Component Function Check 1.INSPECTION START Turn ignition switch OFF. Start engine. Does the engine start? YES >> GO TO 2. NO >> Proceed to EC-456, "Diagnosis Procedure& ...

Other materials:

Normal operating condition
Compass Compass : description Compass The electronic compass is highly protected from changes in most magnetic fields. However, some large changes in magnetic fields can affect it. Some examples are (but not limited to): high tension power lines, large steel buildings, subways, steel ...

Cowl top
Exploded view Cowl top seal Cowl top grille cap Cowl top cover Cowl top extension Cowl top extension insulator Clip EPT seal [t: 3.0 mm (0.12 in) Cowl top cover cap EPT seal [t: 5.0 mm (0.20 in)] Pawl Clip Front Removal and installation COWL TOP COVER Removal Rem ...

Front fog lamp circuit
Description The ipdm e/r (intelligent power distribution module engine room) controls the front fog lamp relay based on inputs from the bcm over the can communication lines. When the front fog lamp relay is energized, power flows from the front fog lamp relay in the ipdm e/r to the front fog ...

В© 2014-2024 Copyright www.nisentra.com