Nissan Sentra Service Manual: Electrical load signal

Nissan Sentra Service Manual / Engine / Engine control system / Dtc/circuit diagnosis / Electrical load signal

Description

The electrical load signal (Headlamp switch signal, rear window defogger switch signal, etc.) is transferred via the CAN communication line.

Component Function Check

1.CHECK REAR WINDOW DEFOGGER SWITCH FUNCTION

With CONSULT

Turn ignition switch ON.
Select вЂњDATA MONITORвЂќ mode of вЂњENGINEвЂќ using CONSULT.
Select вЂњLOAD SIGNALвЂќ and check indication as per the following conditions.

Is the inspection result normal?

Is the inspection result normal? YES >> GO TO 2.

NO >> Proceed to EC-461, "Diagnosis Procedure".

2.CHECK LIGHTING SWITCH FUNCTION

Check вЂњLOAD SIGNALвЂќ indication as per the following conditions. With CONSULT

Check вЂњLOAD SIGNALвЂќ indication as per the following conditions.

Is the inspection result normal?

Is the inspection result normal? YES >> GO TO 3.

NO >> Proceed to EC-461, "Diagnosis Procedure".

3.CHECK HEATER FAN CONTROL SWITCH FUNCTION

Select вЂњHEATER FAN SWвЂќ and check indication as per the following conditions. With CONSULT

Select вЂњHEATER FAN SWвЂќ and check indication as per the following conditions.

Is the inspection result normal?

Is the inspection result normal? YES >> INSPECTION END

NO >> Proceed to EC-461, "Diagnosis Procedure".

Diagnosis Procedure

1.INSPECTION START

Confirm the malfunctioning circuit (rear window defogger, headlamp or heater fan). Refer to EC-461, "Component Function Check".

Which circuit is related to the incident? Rear window defogger>>GO TO 2.

Headlamp>>GO TO 3.

Heater fan>>GO TO 4.

2.CHECK REAR WINDOW DEFOGGER SYSTEM

Check the rear window defogger system. Refer to DEF-27, "Work Flow".

>> INSPECTION END

3.CHECK HEADLAMP SYSTEM

Check the headlamp system. Refer to EXL-85, "Work Flow".

>> INSPECTION END

4.CHECK HEATER FAN CONTROL SYSTEM

Check the heater fan control system. Refer to HA-15, "Workflow".

>> INSPECTION END

Ignition signal

Component Function Check 1.INSPECTION START Turn ignition switch OFF. Start engine. Does the engine start? YES >> GO TO 2. NO >> Proceed to EC-456, "Diagnosis Procedure& ...

Cooling fan

Component Function Check 1.CHECK COOLING FAN FUNCTION With CONSULT Turn ignition switch ON. Perform вЂњFANвЂќ in вЂњACTIVE TESTвЂќ mode of вЂњENGINEвЂќ using CONSULT Check ...

Other materials:

Alarm
The alarm The alarm uses light and sound to give an alert when an intrusion is detected. The alarm is triggered in the following situations when the alarm is set: Vehicles without a smart key system A locked door is unlocked or opened in any way other than using the wireless remote cont ...

Manual transmission (if so equipped)
The ignition switch includes a device that helps prevent accidental removal of the key while driving. The key can only be removed when the ignition switch is in the LOCK position. On manual transmission models, to turn the ignition key to LOCK position from ACC or ON position, turn the ...

B1431, B1433 Seat belt pre-tensioner RH
Description DTC B1431, B1433 SEAT BELT PRE-TENSIONER RH The seat belt pre-tensioner RH is wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor unit will monitor for opens and shorts in detected lines to the seat belt pre-tensioner RH. PART LOCATION Refer to SRC-5, " ...