Nissan Sentra manuals

Nissan Sentra Service Manual: Dtc/circuit diagnosis

Nissan Sentra Service Manual / Driver information & multimedia / Audio, visual & navigation system / Display audio without bose / Dtc/circuit diagnosis

Power supply and ground circuit

Audio unit

AUDIO UNIT : Diagnosis Procedure

Regarding wiring diagram information, refer to av-88, "wiring diagram".

1.Check fuse

Check that the following fuses are not blown.

Are the fuses blown?


Are the fuses blown? Yes >> replace the blown fuse after repairing the affected circuit.

No >> go to 2.

2.Check power supply circuit

  1. Turn ignition switch off.
  2. Disconnect audio unit connector m92.
  3. Check voltage between audio unit connector M92 and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 3.

NO >> Repair or replace harness or connectors.

3.Check ground circuit

  1. Turn ignition switch off.
  2. Disconnect audio unit connector M93.
  3. Check continuity between audio unit connectors and ground.

Is the inspection result normal?


Is the inspection result normal? Yes >> inspection end.

No >> repair or replace harness or connectors.

BluetoothВ® control unit

BLUETOOTHВ® CONTROL UNIT : Diagnosis Procedure

Regarding Wiring Diagram information, refer to AV-88, "Wiring Diagram".

1.Check fuse

Check that the following fuses are not blown.

Are the fuses blown?


Are the fuses blown? Yes >> replace the blown fuse after repairing the affected circuit.

No >> go to 2.

2.Check power supply circuit

  1. Turn ignition switch OFF.
  2. Disconnect bluetoothВ® control unit connector m45.
  3. Check voltage between bluetoothВ® control unit connector m45 and ground.

Is the inspection result normal?


Is the inspection result normal? Yes >> go to 3.

No >> repair or replace harness or connectors.

3.Check ground circuit

  1. Turn ignition switch off.
  2. Check continuity between bluetoothВ® control unit connector m45 and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> Inspection End.

NO >> Repair or replace harness or connectors.

Front door speaker

Diagnosis procedure

Regarding Wiring Diagram information, refer to AV-88, "Wiring Diagram".

1.Connector check

Check the audio unit and speaker connectors for the following:

Is the inspection result normal? Yes >> go to 2

NO >> Repair the terminals or connectors.

2.Check front door speaker signal circuit continuity

  1. Disconnect audio unit connector m92 and suspect front door speaker connector.
  2. Check continuity between audio unit connector m92 and suspect front door speaker connector.


  1. Check continuity between audio unit connector M92 and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 3

NO >> Repair or replace harness or connectors.

3.Check front door speaker signal

  1. Connect audio unit connector m92 and suspect front door speaker connector.
  2. Turn ignition switch to acc.
  3. Push audio unit power switch.
  4. Check signal between the terminals of audio unit connector M92.


Is the inspection result normal?


Is the inspection result normal? Yes >> replace front door speaker. Refer to av-124, "removal and installation".

No >> replace audio unit. Refer to av-122, "removal and installation".

Front tweeter

Diagnosis procedure

Regarding Wiring Diagram information, refer to AV-88, "Wiring Diagram".

1.Connector check

Check the audio unit and speaker connectors for the following:

Is the inspection result normal? YES >> GO TO 2

No >> repair the terminals or connectors.

2.Check front tweeter signal circuit continuity

  1. Disconnect audio unit connector M92 and suspect front tweeter connector.
  2. Check continuity between audio unit connector m92 and suspect front tweeter connector.


  1. Check continuity between audio unit connector M92 and ground.

Is the inspection result normal?


Is the inspection result normal? Yes >> go to 3

No >> repair or replace harness or connectors.

3.Check front tweeter signal

  1. Connect audio unit connector m92 and suspect front tweeter connector.
  2. Turn ignition switch to ACC
  3. Push audio unit POWER switch.
  4. Check signal between the terminals of audio unit connector m92.


Is the inspection result normal?


Is the inspection result normal? Yes >> replace front tweeter. Refer to av-123, "removal and installation".

No >> replace audio unit. Refer to av-122, "removal and installation".

Rear speaker

Diagnosis procedure

Regarding Wiring Diagram information, refer to AV-88, "Wiring Diagram".

1.Connector check

Check the audio unit and speaker connectors for the following:

Is the inspection result normal? YES >> GO TO 2

No >> repair the terminals or connectors.

2.Check rear speaker signal circuit continuity

  1. Disconnect audio unit connector m92 and suspect rear speaker connector.
  2. Check continuity between audio unit connector M92 and suspect rear speaker connector.


  1. Check continuity between audio unit connector M92 and ground.

Is the inspection result normal?


Is the inspection result normal? Yes >> go to 3

No >> repair or replace harness or connectors.

3.Check rear speaker signal

  1. Connect audio unit connector m92 and suspect rear speaker connector.
  2. Turn ignition switch to acc.
  3. Push audio unit power switch.
  4. Check signal between the terminals of audio unit connector m92.


Is the inspection result normal?


Is the inspection result normal? Yes >> replace rear speaker. Refer to av-125, "removal and installation".

No >> replace audio unit. Refer to av-122, "removal and installation".

BluetoothВ® voice signal circuit

Diagnosis procedure

Regarding wiring diagram information, refer to av-88, "wiring diagram".

1.Check bluetoothВ® voice signal circuit continuity

  1. Turn ignition switch off.
  2. Disconnect audio unit connector m93 and bluetoothВ® control unit connector m45.
  3. Check continuity between audio unit connector M93 and BluetoothВ® control unit connector M45.


  1. Check continuity between audio unit connector M93 and ground.

Is inspection result normal?


Is inspection result normal? Yes >> go to 2.

No >> repair or replace harness or connectors.

2.Check bluetoothВ® voice signal ground circuit continuity

Check continuity between audio unit connector m93 and bluetoothВ® control unit connector m45.

Is inspection result normal?


Is inspection result normal? Yes >> go to 3.

No >> repair or replace harness or connectors.

3.Check bluetoothВ® voice signal

  1. Connect audio unit connector M93 and BluetoothВ® control unit connector M45.
  2. Turn ignition switch to acc.
  3. Press Check signal between the terminals of audio unit connector M93. switch.

  4. Check signal between the terminals of audio unit connector M93.


Is the inspection result normal? Yes >> replace bluetoothВ® control unit. Refer to av-134, "removal and installation".

No >> replace audio unit. Refer to av-122, "removal and installation".

BluetoothВ® control signal circuit

Diagnosis procedure

Regarding wiring diagram information, refer to av-88, "wiring diagram".

1.Check control signal circuit continuity

  1. Turn ignition switch off
  2. Disconnect BluetoothВ® control unit connector M45.
  3. Check continuity between bluetoothВ® control unit connector m45 and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> Replace BluetoothВ® control unit. Refer to AV-134, "Removal and Installation".

NO >> Repair or replace harness or connectors.

Microphone signal circuit

Diagnosis Procedure

Regarding wiring diagram information, refer to av-88, "wiring diagram".

1.Check harness between bluetoothВ® control unit and microphone

  1. Turn ignition switch off.
  2. Disconnect bluetoothВ® control unit connector m45 and microphone connector r4.
  3. Check continuity between BluetoothВ® control unit connector M45 and microphone connector R4.


  1. Check continuity between BluetoothВ® control unit connector M45 and ground.

Are continuity results as specified?


Are continuity results as specified? Yes >> go to 2

NO >> Repair harness or connectors.

2.Check microphone power supply

  1. Connect bluetoothВ® control unit connector m45 and microphone connector r4.
  2. Turn ignition switch on.
  3. Check voltage between microphone connector r4 and ground.

Is the voltage reading as specified?


Is the voltage reading as specified? Yes >> go to 3

No >> replace bluetoothВ® control unit. Refer to av-134, "removal and installation".

3.Check microphone signal

Check signal between terminals of BluetoothВ® control unit connector M45.

Were voltage readings as specified?


Were voltage readings as specified? Yes >> replace bluetoothВ® control unit. Refer to av-134, "removal and installation".

No >> replace microphone. Refer to av-135, "removal and installation".

Steering switch

Diagnosis procedure

Regarding wiring diagram information, refer to av-88, "wiring diagram".

1.Check steering wheel audio control switch resistance

  1. Turn ignition switch OFF.
  2. Disconnect combination switch (spiral cable) connector m79.
  3. Check resistance between the terminals of combination switch (spiral cable) connector m79.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 2.

NO >> Replace steering switches. Refer to AV-208, "Removal and Installation".

2.Check harness between bluetoothВ® control unit and combination switch (spiral cable)

  1. Disconnect bluetoothВ® control unit connector m45 and combination switch (spiral cable) connector m80.
  2. Check continuity between bluetoothВ® control unit connector m45 and combination switch (spiral cable) connector m80.


  1. Check continuity between BluetoothВ® control unit connector M45 and ground.

Is the inspection result normal?


Is the inspection result normal? Yes >> go to 3.

NO >> Repair or replace harness or connectors.

3.Check combination switch (spiral cable)

Check continuity between combination switch (spiral cable) connectors m79 and m80.

Is the inspection result normal?


Is the inspection result normal? Yes >> go to 4.

No >> replace combination switch (spiral cable). Refer to sr-16, "removal and installation".

4.Check harness between bluetoothВ® control unit and audio unit

  1. Disconnect audio unit connector M92.
  2. Check continuity between BluetoothВ® control unit connector M45 and audio unit connector M92.


  1. Check continuity between BluetoothВ® control unit connector M45 and ground.

Is the inspection result normal?


Is the inspection result normal? Yes >> replace audio unit. Refer to av-203, "removal and installation".

No >> repair or replace harness or connectors.

Usb connector

Diagnosis Procedure

Regarding Wiring Diagram information, refer to AV-88, "Wiring Diagram".

1.Check usb interface harness continuity

  1. Turn ignition switch off.
  2. Disconnect audio unit connector m97 and usb interface connector m132.
  3. Check continuity between audio unit connector m97 and usb interface connector m132.


  1. Check continuity between audio unit connector M97 and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> Replace the USB interface. Refer to AV-132, "Removal and Installation".

NO >> Repair or replace harness or connectors.

Basic inspection
Diagnosis and repair workflow Work Flow Overall sequence Detailed flow 1.Get information for symptom Get detailed information from the customer about the symptom (the condition and the envi ...

Symptom diagnosis
Audio system Symptom table Related to audio Related to hands-free phone Before performing diagnosis, confirm that the cellular phone being used by the customer is compatible with t ...

Other materials:

P0712 Transmission fluid temperature sensor A
DTC Logic DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection condition Possible causes P0712 FLUID TEMP SENSOR A (Transmission Fluid Temperature Sensor A Circuit Low) The CVT fluid temperature identified by the TCM is 1 ...

Ignition timing
Inspection 1.CHECK IGNITION TIMING Attach timing light to the ignition coil No.1 harness. Check ignition timing. : Timing indicator Specification : EC-486, "Ignition Timing" >> INSPECTION END ...

Diagnosis system (BCM)
Common item Common item : consult function (bcm - common item) Application item Consult performs the following functions via can communication with bcm. Direct diagnostic mode Description Ecu identification The bcm part number is displayed. Self Diagnostic Result ...

© 2014-2026 Copyright www.nisentra.com