Nissan Sentra manuals

Nissan Sentra Service Manual: CVT Shift selector

Exploded View


  1. Shift selector knob
  2. Lock pin
  3. Knob cover
  4. Position indication panel
  5. Detent switch
  6. Shift lock unit
  7. Park position switch
  8. Shift selector assembly
  9. Shift selector harness assembly
  10. Position bulb
  11. Key interlock rod
  1. With push-button ignition switch system
  2. Without push-button ignition switch system

Removal and Installation

REMOVAL

  1. Turn ignition switch OFF.
  2. Move the shift selector to “N” position
  3. Remove shift selector knob with the following procedure.
  1. Slide the knob cover (1) down.

CAUTION:

Do not damage the knob cover.

  1. Pull out the lock pin (2).
  2. Pull the shift selector knob (3) and knob cover upwards to remove them.
  1. Remove the center console. Refer to IP-17, "Removal and Installation".
  2. Remove rear floor duct (LH/RH). Refer to VTL-8, "Exploded View".


  1. Move the shift selector to “P” position.
  2. Remove the key interlock cable from the shift selector assembly. Refer to TM-260, "Removal and Installation".

    (Without push-button ignition switch)

  3. Remove the control cable from the shift selector assembly with the following procedure.
  1. Disconnect the tip (A) of control cable from the shift selector assembly.
  2. Remove socket (B) from shift selector assembly.
  1. Remove harness clips from the shift selector with a clip remover.
  2. Remove shift selector nuts.
  3. Remove the shift selector assembly from the vehicle.

INSTALLATION


INSTALLATION

Installation is in the reverse order of removal.

NOTE:

Pay attention to the following when connecting the control cable to the shift selector assembly.

  1. When connecting the control cable (1) to the shift selector assembly (2), face the grooved surface of the rib (A) up and insert the control cable until it stops.


  1. Install the socket (A) onto the shift selector assembly.

CAUTION:


  1. Follow the procedure below and place the shift selector knob onto the shift selector.
  1. Install the lock pin (2) onto the shift selector knob (3).
  2. Move the shift selector to “N” position.
  3. Insert the shift selector knob into the shift selector until a slight touch is felt.
  4. Press and hold the shift selector knob button and insert shift selector knob onto shift selector until it clicks.

CAUTION:


CAUTION:

Do not strike the shift selector knob to press it into place.

  1. After installing shift selector knob, pull the knob to check that it does not become disconnected.

Inspection

INSPECTION

Check the CVT position. If a malfunction is found, adjust the CVT position. Refer to TM-150, "Inspection".

Removal and installation
...

Control cable
Exploded View Control cable Lock plate Transaxle assembly Bracket A Bracket B CVT shift selector assembly Manual lever Grommet Removal and Installation INSTALLATION CA ...

Other materials:

Precaution
Precaution for supplemental restraint system (srs) "air bag" and "seat belt pre-tensioner" The supplemental restraint system such as “air bag” and “seat belt pre-tensioner”, used along with a front seat belt, helps to reduce the risk or severity of injur ...

Remote keyless entry system (if so equipped)
WARNING Radio waves could adversely affect electric medical equipment. Those who use a pacemaker should contact the electric medical equipment manufacturer for the possible influences before use. The remote keyless entry keyfob transmits radio waves when the bu ...

P014C, P014D, P015A, P015B A/F Sensor 1
DTC Logic DTC DETECTION LOGIC To judge the malfunction of A/F sensor 1, this diagnosis measures response time of the A/F signal computed by ECM from the A/F sensor 1 signal. The time is compensated by engine operating (speed and load), fuel feedback control constant, and the A/F sensor 1 tem ...

© 2014-2024 Copyright www.nisentra.com