Nissan Sentra manuals

Nissan Sentra Service Manual: C1716, C1717, C1718, C1719 Transmitter (pressure data)

Nissan Sentra Service Manual / Suspension / Road wheels & Tires / DTC/Circuit diagnosis / C1716, C1717, C1718, C1719 Transmitter (pressure data)

DTC Logic

NOTE:

The Signal Tech II Tool (J-50190) can be used to perform the following functions. Refer to the Signal Tech II User Guide for additional information.

DTC DETECTION LOGIC

DTC

Display Item

Malfunction detected condition

Possible causes

C1716 [PRESSDATA ERR] FL Malfunction in the tire pressure data from the front LH wheel transmitter.
  • Transmitter ID registration incomplete
  • Transmitter malfunction
C1717 [PRESSDATA ERR] FR Malfunction in the tire pressure data from the front RH wheel transmitter.
C1718 [PRESSDATA ERR] RR Malfunction in the tire pressure data from the rear RH wheel transmitter.
C1719 [PRESSDATA ERR] RL Malfunction in the tire pressure data from the rear LH wheel transmitter.

DTC CONFIRMATION PROCEDURE

1.PERFORM SELF DIAGNOSTIC RESULT

With CONSULT


  1. Turn the ignition switch ON.
  2. Check the tire pressure for all wheels and adjust to the specified value. Refer to WT-54, "Tire Air Pressure".
  3. Perform “SELF DIAGNOSTIC RESULT”.

Is DTC “C1716”, “C1717”, “C1718”, or “C1719” detected? YES >> Proceed to WT-30, "Diagnosis Procedure".

NO >> Inspection End.

Diagnosis Procedure

NOTE:

The Signal Tech II Tool (J-50190) can be used to perform the following functions. Refer to the Signal Tech II User Guide for additional information.

1.CHECK TIRE PRESSURE

Check the air pressure of all wheels. Refer to pressure observed during “DTC CONFIRMATION PROCEDURE”.

Is the inspection result normal? YES >> Replace the DTC-detected malfunctioning transmitter. Refer to WT-50, "Removal and Installation".

NO >> GO TO 2.

2.CHECK TIRE PRESSURE SIGNAL

With CONSULT


  1. Perform transmitter ID registration for all wheels. Refer to WT-22, "Work Procedure".
  2. Drive for 3 minutes at a speed of 40 km/h (25 MPH) or more, then drive normally for 10 minutes.
  3. Stop the vehicle.
  4. On “DATA MONITOR” select “AIR PRESS FL”, “AIR PRESS FR”, “AIR PRESS RR” and “AIR PRESS RL”.
  5. Within 5 minutes after vehicle is stopped, read the values displayed on CONSULT.

Are tire pressures displayed as 438.6 kPa (4.47 kg/cm2, 63.6 psi)? YES >> Replace transmitter for the tire that displayed pressure as 438.6 kPa (4.47 kg/cm2, 63.6 psi).

Refer to WT-50, "Removal and Installation".

NO >> Perform “DTC CONFIRMATION PROCEDURE” again. Refer to WT-30, "DTC Logic".

C1708, C1709, C1710, C1711 Transmitter (no data)
DTC Logic NOTE: The Signal Tech II Tool (J-50190) can be used to perform the following functions. Refer to the Signal Tech II User Guide for additional information. Activate and display TPMS ...

C1729 Vehicle speed signal
DTC Logic NOTE: The Signal Tech II Tool (J-50190) can be used to perform the following functions. Refer to the Signal Tech II User Guide for additional information. Activate and display TPMS ...

Other materials:

Heater and Air Conditioner (manual) (if so equipped)
WARNING The air conditioner cooling function operates only when the engine is running. Do not leave children or adults who would normally require the assistance of others alone in your vehicle. Pets should also not be left alone. They could accidentally injure them ...

Vacuum lines
Exploded View Clamp Vacuum hose (built-in check valve) Vacuum piping Vacuum hose To intake manifold side Paint mark Stamp indicating engine direction To brake booster Removal and Installation REMOVAL Remove air duct and air cleaner case. Refer to EM-25, "Remova ...

RCTA function - RCTA (Rear Cross Traffic Alert)
The RCTA functions when your vehicle is in reverse. It can detect other vehicles approaching from the right or left rear of the vehicle. It uses radar sensors to alert the driver of the other vehicle's existence through flashing the outside rear view mirror indicators and sounding a buzzer. ...

© 2014-2024 Copyright www.nisentra.com