Nissan Sentra Service Manual: C1105, C1106, C1107, C1108 Wheel sensor

Nissan Sentra Service Manual / Brakes / Brake control system / Dtc/circuit diagnosis / C1105, C1106, C1107, C1108 Wheel sensor

Description

When the sensor rotor rotates, the magnetic field changes. It converts the magnetic field changes to current signals (rectangular wave) and transmits them to the ABS actuator and electric unit (control unit).

DTC Logic

DTC DETECTION LOGIC

DTC	Display Item	Malfunction detected condition	Possible causes
C1105	RR RH SENSOR-2	When distance between rear wheel sensor RH and rear wheel sensor RH rotor is large. When installation of rear wheel sensor RH or rear wheel sensor RH rotor is not normal.	Wheel sensor ABS actuator and electric unit (control unit) Sensor rotor
C1106	RR LH SENSOR-2	When distance between rear wheel sensor LH and rear wheel sensor LH rotor is large. When installation of rear wheel sensor LH or rear wheel sensor LH rotor is not normal.
C1107	FR RH SENSOR-2	When distance between front wheel sensor RH and front wheel sensor RH rotor is large. When installation of front wheel sensor RH or front wheel sensor RH rotor is not normal.
C1108	FR LH SENSOR-2	When distance between front wheel sensor LH and front wheel sensor LH rotor is large. When installation of front wheel sensor LH or front wheel sensor LH rotor is not normal.

DTC CONFIRMATION PROCEDURE

1.CHECK SELF DIAGNOSTIC RESULT

With CONSULT.

Start engine and drive vehicle at approximately 21 km/h (13 MPH) or more for approximately 5 minutes.
Perform self diagnostic result.

Is DTC C1105, C1106, C1107 or C1108 detected? YES >> Proceed to diagnosis procedure. Refer to BRC-60, "Diagnosis Procedure".

NO >> Inspection End.

Diagnosis Procedure

Regarding Wiring Diagram information, refer to BRC-44, "Wiring Diagram".

CAUTION:

Do not check between wheel sensor terminals.

1.CONFIRM DTC

With CONSULT

Perform self-diagnostic result of ABS and record all active DTCs.
Clear all DTCs.
Perform DTC confirmation procedure. Refer to BRC-60, "DTC Logic".

Does DTC C1105, C1106, C1107 or C1108 reset? YES >> GO TO 2.

NO >> Refer to GI-39, "Intermittent Incident".

2.CHECK TIRE PRESSURE AND TIRE WEAR

Check tires for excessive wear and proper inflation. Refer to WT-54, "Tire Air Pressure".

Is the inspection result normal? YES >> GO TO 3.

NO >> Repair or replace as necessary.

3.CHECK WHEEL SENSOR

Check wheel sensor for the following:

Proper installation
Physical damage
Contamination

Is the inspection result normal? YES >> GO TO 4.

NO >> Repair or replace as necessary.

4.CHECK SENSOR ROTOR

Check sensor rotor for the following:

Contamination
Physical damage (missing teeth, cracks, etc.)
Foreign material
Looseness

Is the inspection result normal? YES >> Replace the wheel sensor. Refer to BRC-106, "FRONT WHEEL SENSOR : Removal and Installation" or BRC-107, "REAR WHEEL SENSOR : Removal and Installation" . Then, GO TO 5.

NO >> Repair or replace as necessary.

5.CONFIRM REPAIR

With CONSULT

Clear all DTCs.
Perform DTC confirmation procedure. Refer to BRC-60, "DTC Logic".

Does DTC C1105, C1106, C1107 or C1108 reset? YES >> Replace ABS actuator and electric unit (control unit). Refer to BRC-110, "Removal and Installation".

NO >> Inspection End.

C1101, C1102, C1103, C1104 Wheel sensor

Description When the sensor rotor rotates, the magnetic field changes. It converts the magnetic field changes to current signals (rectangular wave) and transmits them to the ABS actuator and elec ...

C1109 Power and ground system

DTC Logic DTC DETECTION LOGIC DTC Display Item Malfunction detected condition Possible causes C1109 BATTERY VOLTAGE [ABNORMAL] When ignition voltage is 10 ...

Other materials:

Automatic door locks
All doors lock automatically when the vehicle speed reaches 15 MPH (24 km/h). All doors unlock automatically when the ignition is placed in the OFF position (models with Intelligent Key system) or when the key is removed from the ignition switch (models without Intelligent Key system) ...

P0182, P0183 FTT Sensor
DTC Logic DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition Possible cause P0182 FTT SEN/CIRCUIT (Fuel temperature sensor ″A″ circuit low) An excessively low voltage from the sensor is sent to ...

When traveling or registering your vehicle in another country
When planning to drive your NISSAN vehicle in another country, you should first find out if the fuel available is suitable for your vehicle’s engine. Using fuel with an octane rating that is too low may cause engine damage. All gasoline vehicles must be operated with unleaded gasoline. The ...