Nissan Sentra manuals

Nissan Sentra Service Manual: Basic inspection

Diagnosis and repair workflow

Work flow (with exp-800 ni or gr8-1200 ni)

CHARGING SYSTEM DIAGNOSIS WITH EXP-800 NI OR GR8-1200 NI

To test the charging system, use the following special service tools:

NOTE:

Refer to the applicable Instruction Manual for proper charging system diagnosis procedures.

Revision:

OVERALL SEQUENCE

DETAILED FLOW


DETAILED FLOW

NOTE:

To ensure a complete and thorough diagnosis, the battery, stater and generator test segments must be done as a set from start to finish.

1.PRELIMINARY INSPECTION

Perform the preliminary inspection. Refer to CHG-20, "Diagnosis Procedure".

>> GO TO 2.

2.STOP POWER GENERATION VOLTAGE VARIABLE CONTROL SYSTEM

Stop the operation of the power generation voltage variable control in either of the following procedures.

>> GO TO 3.

3.DIAGNOSIS WITH EXP-800 NI OR GR8-1200 NI

Perform the charging system test using Multitasking battery and electrical diagnostic station GR8-1200 NI or Battery and electrical diagnostic analyzer EXP-800 NI. Refer to the applicable Instruction Manual for proper testing procedures.

Test result

NO PROBLEMS>>Charging system is normal and will also show “DIODE RIPPLE” test result.

NO VOLTAGE>>GO TO 4.

LOW VOLTAGE>>GO TO 12.

HIGH VOLTAGE>>GO TO 14.

EXCESSIVE RIPPLE, OPEN PHASE, OPEN DIODE or SHORTED DIODE>>Replace the generator. Refer to CHG-29, "Removal and Installation". Perform “DIODE RIPPLE” test again using Multitasking battery and electrical diagnostic station GR8-1200 NI or Battery and electrical diagnostic analyzer EXP-800 NI to confirm repair.

4.INSPECTION WITH CHARGE WARNING LAMP (IGNITION SWITCH IS ON)

Turn the ignition switch ON.

Does the charge warning lamp illuminate? YES >> GO TO 6.

NO >> GO TO 5.

5.“L” TERMINAL CIRCUIT (OPEN) INSPECTION

Check “L” terminal circuit (open). Refer to CHG-24, "Diagnosis Procedure".

Is the “L” terminal circuit normal? YES >> Replace generator. Refer to CHG-29, "Removal and Installation".

NO >> Repair as needed.

6.INSPECTION WITH CHARGE WARNING LAMP (IDLING)

Start the engine and run it at idle.

Does the charge warning lamp turn OFF? YES >> GO TO 9.

NO >> GO TO 7.

7.“L” TERMINAL CIRCUIT (SHORT) INSPECTION

Check “L” terminal circuit (short). Refer to CHG-26, "Diagnosis Procedure".

Is the “L” terminal circuit normal? YES >> GO TO 8.

NO >> Repair as needed.

8.“S” TERMINAL CIRCUIT INSPECTION

Check “S” terminal circuit. Refer to CHG-27, "Diagnosis Procedure".

Is the “S” terminal circuit normal? YES >> GO TO 10.

NO >> Repair as needed.

9.INSPECTION WITH CHARGE WARNING LAMP (ENGINE AT 3,000 RPM)

Increase and maintain the engine speed at 3,000 rpm.

Does the charge warning lamp remain off? YES >> GO TO 11.

NO >> GO TO 10.

10.INSPECTION OF GENERATOR PULLEY

Check generator pulley. Refer to CHG-30, "Inspection".

Is generator pulley normal? YES >> Replace generator. Refer to CHG-29, "Removal and Installation".

NO >> Repair as needed.

11.“B” TERMINAL CIRCUIT INSPECTION

Check “B” terminal circuit. Refer to CHG-23, "Diagnosis Procedure".

Is “B” terminal circuit normal? YES >> Replace generator. Refer to CHG-29, "Removal and Installation".

NO >> Repair as needed.

12.“B” TERMINAL CIRCUIT INSPECTION

Check “B” terminal circuit. Refer to CHG-23, "Diagnosis Procedure".

Is “B” terminal circuit normal? YES >> GO TO 13.

NO >> Repair as needed.

13.INSPECTION OF GENERATOR PULLEY

Check generator pulley. Refer to CHG-30, "Inspection".

Is generator pulley normal? YES >> Replace generator. Refer to CHG-29, "Removal and Installation".

NO >> Repair as needed.

14.“S” TERMINAL CIRCUIT INSPECTION

Check “S” terminal circuit. Refer to CHG-27, "Diagnosis Procedure".

Is the “S” terminal circuit normal? YES >> Replace generator. Refer to CHG-29, "Removal and Installation".

NO >> Repair as needed.

Work flow (without exp-800 ni or gr8-1200 ni).

OVERALL SEQUENCE

Before performing a generator test, make sure that the battery is fully charged. A 30-volt voltmeter and suitable test probes are necessary for the test.

DETAILED FLOW


DETAILED FLOW

1.PRELIMINARY INSPECTION

Perform the preliminary inspection. Refer to CHG-20, "Diagnosis Procedure".

>> GO TO 2.

2.STOP POWER GENERATION VOLTAGE VARIABLE CONTROL SYSTEM

Stop the operation of the power generation voltage variable control in either of the following procedures:

>> GO TO 3.

3.INSPECTION WITH CHARGE WARNING LAMP (IGNITION SWITCH IS TURNED ON)

When ignition switch is turned ON.

Does the charge warning lamp illuminate?

YES >> GO TO 4.

NO >> GO TO 10.

4.INSPECTION WITH CHARGE WARNING LAMP (IDLING)

Start the engine and run it at idle

Does the charge warning lamp turn OFF? YES >> GO TO 5.

NO >> GO TO 6.

5.INSPECTION WITH CHARGE WARNING LAMP (ENGINE AT 2,500 RPM)

Increase and maintain the engine speed at 2,500 rpm.

Does the charge warning lamp illuminate? YES >> GO TO 8.

NO >> Inspection End.

6.“L” TERMINAL CIRCUIT (SHORT) INSPECTION

Check terminal “L” circuit for (short). Refer to CHG-26, "Diagnosis Procedure".

Is the inspection result normal? YES >> GO TO 7.

NO >> Repair as needed.

7. “S” TERMINAL CIRCUIT INSPECTION

Check terminal “S” circuit. Refer to CHG-27, "Diagnosis Procedure".

Is the inspection result normal? YES >> GO TO 8.

NO >> Repair as needed.

8.MEASURE “B” TERMINAL VOLTAGE

Start engine. With engine running at 2,500 rpm, measure “B” terminal voltage.

What voltage does the measurement result show? Less than 13.0 V>>GO TO 9.

More than 16.0 V>>Replace generator. Refer to CHG-29, "Removal and Installation".

9.“B” TERMINAL CIRCUIT INSPECTION

Check “B” terminal circuit. Refer to CHG-23, "Diagnosis Procedure".

Is the inspection result normal? YES >> Replace generator. Refer to CHG-29, "Removal and Installation".

NO >> Repair as needed.

10.INSPECTION WITH CHARGE WARNING LAMP (IGNITION SWITCH

 IS ON)

  1. Disconnect generator connector and apply ground to “L” terminal.
  2. Turn the ignition switch ON.

Does the charge warning lamp illuminate? YES >> Replace generator. Refer to CHG-29, "Removal and Installation".

NO >> GO TO 11.

11.CHECK “L” TERMINAL CIRCUIT (OPEN)

Check “L” terminal circuit (OPEN). Refer to CHG-26, "Diagnosis Procedure".

>> Repair as needed.

Wiring diagram
Charging system Wiring Diagram ...

Dtc/circuit diagnosis
...

Other materials:

Electrical load signal
Description The electrical load signal (Headlamp switch signal, rear window defogger switch signal, etc.) is transferred via the CAN communication line. Component Function Check 1.CHECK REAR WINDOW DEFOGGER SWITCH FUNCTION With CONSULT Turn ignition switch ON. Select “DATA MONITORР...

Diagnosis system (bcm) (with intelligent key system)
Common item Common item : consult function (bcm - common item) APPLICATION ITEM CONSULT performs the following functions via CAN communication with BCM. Direct Diagnostic Mode Description ECU identification The BCM part number is displayed. Self Diagnostic Result ...

Battery saver output/power supply circuit
Description Provides the battery saver output/power supply. Also cuts the power supply when the interior lamp battery saver is activated. Component function check 1.Check battery saver output/power supply function Consult Turn ignition switch on. Turn each interior lamp to the ON posit ...

© 2014-2024 Copyright www.nisentra.com