Nissan Sentra manuals

Nissan Sentra Service Manual: Additional service when replacing ecm

Nissan Sentra Service Manual / Engine / Engine control system / Basic inspection / Additional service when replacing ecm

Description

When replacing ECM, the following procedure must be performed. (For details, refer to EC-135, "Work Procedure".)

PROGRAMMING OPERATION

NOTE:

After replacing with a blank ECM, programming is required to write ECM information. Be sure to follow the procedure to perform the programming.

Work Procedure

1.SAVE ECM DATA

With CONSULT


  1. Turn ignition switch OFF.
  2. Reconnect all harness connectors disconnected.
  3. Turn ignition switch ON.
  4. Select “SAVING DATA FOR REPLC CPU” in “WORK SUPPORT” mode of “ENGINE” using CONSULT.
  5. Follow the instruction of CONSULT display

NOTE:

>> GO TO 2.

2.CHECK ECM PART NUMBER

Check ECM part number to see whether it is blank ECM or not.

NOTE:

Is the ECM a blank ECM? YES >> GO TO 3.

NO >> GO TO 5.

3.SAVE ECM PART NUMBER

Read out the part number from the old ECM and save the number, following the programming instructions.

Refer to CONSULT Operation Manual.

NOTE:

>> GO TO 4.

4.PERFORM ECM PROGRAMMING

After replacing ECM, perform the ECM programming. Refer to CONSULT Operation Manual.

NOTE:

>> GO TO 6.

5.REPLACE ECM

Replace ECM. Refer to EC-485, "Removal and Installation".

>> GO TO 6.

6.PERFORM INITIALIZATION OF IVIS (NATS) SYSTEM AND REGISTRATION OF ALL IVIS (NATS) IGNITION KEY IDS

Refer to SEC-61, "ECM : Work Procedure" (With Intelligent Key System) or SEC-174, "ECM : Work Procedure" (Without Intelligent Key System).

>> GO TO 7.

7.CHECK ECM DATA STATUS

Check if the data is successfully copied from the ECM at Step 1 (before replacement) and saved in CONSULT.

Is the data saved successfully? YES >> GO TO 8.

NO >> GO TO 9.

8.WRITE ECM DATA

With CONSULT


  1. Select “WRITING DATA FOR REPLC CPU” in “WORK SUPPORT” mode of “ENGINE” using CONSULT
  2. Follow the instruction of CONSULT display.

NOTE:

The data saved by “SAVING DATA FOR REPLC CPU” is written to ECM.

>> GO TO 10.

9.PERFORM VIN REGISTRATION

Refer to EC-137, "Work Procedure".

>> GO TO 10.

10.PERFORM ACCELERATOR PEDAL RELEASED POSITION LEARNING

Perform Accelerator Pedal Released Position Learning. Refer to EC-138, "Work Procedure".

>> GO TO 11.

11.PERFORM THROTTLE VALVE CLOSED POSITION LEARNING

Perform Throttle Valve Closed Position Learning. Refer to EC-139, "Work Procedure".

>> GO TO 12.

12.PERFORM IDLE AIR VOLUME LEARNING

Perform Idle Air Volume Learning. Refer to EC-140, "Work Procedure".

>> END

Basic inspection
Work Procedure 1.INSPECTION START Check service records for any recent repairs that may indicate a related malfunction, or a current need for scheduled maintenance. Open engine hood and ch ...

Vin registration
Description VIN Registration is an operation to registering VIN in ECM. It must be performed each time ECM is replaced. NOTE: Accurate VIN which is registered in ECM may be required for Inspectio ...

Other materials:

System description
Component parts Component parts location Front tweeter LH GPS antenna Steering switches AV control unit Front tweeter RH Microphone Front door speaker LH Front door speaker RH Rear door speaker LH Rear door speaker RH Rear woofer RH Rear woofer LH Antenna amp Satel ...

Diagnosis system (ipdm e/r) (without intelligent key system)
Diagnosis Description AUTO ACTIVE TEST Description In auto active test, the IPDM E/R sends a drive signal to the following systems to check their operation. Front wiper (LO, HI) Parking lamp License plate lamp Tail lamp Front fog lamp (if equipped) Headlamp (LO, HI) A/C compres ...

On Board Diagnostic (OBD) System of Engine and CVT
The ECM has an on board diagnostic system. It will light up the malfunction indicator lamp (MIL) to warn the driver of a malfunction causing emission deterioration. CAUTION: Be sure to turn the ignition switch OFF and disconnect the negative battery cable before any repair or inspection ...

© 2014-2025 Copyright www.nisentra.com