Toyota Camry owners & service manuals

Toyota Camry: Wheels

If a wheel is bent, cracked or heavily corroded, it should be replaced. Otherwise, the tire may separate from the wheel or cause a loss of handling control.

Wheel selection

When replacing wheels, care should be taken to ensure that they are equivalent to those removed in load capacity, diameter, rim width and inset*.

Replacement wheels are available at your Toyota dealer.

*: Conventionally referred to as "offset".

Toyota does not recommend using the following:

  • Wheels of different sizes or types
  • Used wheels
  • Bent wheels that have been straightened

Aluminum wheel precautions (if equipped)

  • Use only Toyota wheel nuts and wrenches designed for use with your aluminum wheels.
  • When rotating, repairing or changing your tires, check that the wheel nuts are still tight after driving 1000 miles (1600 km).
  • Be careful not to damage the aluminum wheels when using tire chains.
  • Use only Toyota genuine balance weights or equivalent and a plastic or rubber hammer when balancing your wheels.

■When replacing wheels

The wheels of your vehicle are equipped with tire pressure warning valve and transmitters that allow the tire pressure warning system to provide advance warning in the event of a loss in tire inflation pressure. Whenever wheels are replaced, tire pressure warning valve and transmitters must be installed.

WARNING

■When replacing wheels

  • Do not use wheels that are a different size from those recommended in the Owner's Manual, as this may result in a loss of handling control.
  • Never use an inner tube in a leaking wheel which is designed for a tubeless tire. Doing so may result in an accident, causing death or serious injury.

■When installing the wheel nuts

  • Be sure to install the wheel nuts with the tapered ends facing inward.

    Installing the nuts with the tapered ends facing outward can cause the wheel to break and eventually cause the wheel to come off while driving, which could lead to an accident resulting in death or serious injury.

  • Never use oil or grease on the wheel bolts or wheel nuts.

    Oil and grease may cause the wheel nuts to be excessively tightened, leading to bolt or disc wheel damage. In addition, the oil or grease can cause the wheel nuts to loosen and the wheel may fall off, causing an accident and resulting in death or serious injury. Remove any oil or grease from the wheel bolts or wheel nuts.

NOTICE

■Replacing tire pressure warning valve and transmitters

  • Because tire repair or replacement may affect the tire pressure warning valve and transmitters, make sure to have tires serviced by your Toyota dealer or other qualified service shop. In addition, make sure to purchase your tire pressure warning valve and transmitters at your Toyota dealer.
  • Ensure that only genuine Toyota wheels are used on your vehicle.

    Tire pressure warning valve and transmitters may not work properly with non-genuine wheels.

    READ NEXT:

     Air conditioning filter

    The air conditioning filter must be changed regularly to maintain air conditioning efficiency. Removal method 1. Turn the engine switch off. 2. Open the glove box and remove the glove box cover

     Wireless remote control/electronic key battery

    Replace the battery with a new one if it is depleted. You will need the following items: Flathead screwdriver Small flathead screwdriver Lithium battery CR2032 Replacing the battery Vehic

     Checking and replacing fuses

    If any of the electrical components do not operate, a fuse may have blown. If this happens, check and replace the fuses as necessary. 1. Turn the engine switch off. 2. Open the fuse box cover. Eng

    SEE MORE:

     Checking and replacing fuses

    If any of the electrical components do not operate, a fuse may have blown. If this happens, check and replace the fuses as necessary. 1. Turn the engine switch off. 2. Open the fuse box cover. Engine compartment (type A) Push the tabs in and lift the lid off. Engine compartment (type B) (if

     How To Proceed With Troubleshooting

    CAUTION / NOTICE / HINT HINT: Use the following procedure to troubleshoot the blind spot monitor system. *: Use the Techstream. PROCEDURE 1. VEHICLE BROUGHT TO WORKSHOP NEXT 2. CUSTOMER PROBLEM ANALYSIS HINT: If there are any s

    © 2023-2024 Copyright www.tocamry.com