Toyota Camry Owner's Manual (2023): Settings display
â—† Changing settings
Use the meter control switches on the steering wheel to change settings.
1. Press 
or
to select
.
2. Operate the switches to select a desired item.
3. Press or press and hold 
.
The available settings will differ depending on if
is pressed or
pressed and held. Follow the instructions on the display.
â—† Setting items
â– 
LTA (Lane Tracing Assist)
Press and hold to change the
settings of the following items:
â– 
PCS (Pre-Collision System)
Press and hold to change the
settings of the following items:
â– 
DRCC (Dynamic Radar Cruise
Control)
Press and hold to change the
settings of the following item:
â– 
BSM (Blind Spot Monitor) (if
equipped)
Press to enable/disable the Blind
Spot Monitor function.
Press and hold to change the
settings of the following item:
â– 
RCTA (Rear Cross Traffic
Alert) (if equipped)
Press to enable/disable the Rear
Cross Traffic Alert function.
Press and hold to change the
settings of the following item:
â– RCD (Rear Camera Detection) function (if equipped)
Press to enable/disable the rear
camera detection function.
â– 
PKSB (Parking Support
Brake) (if equipped)
Press to enable/disable the
Parking Support Brake.
â– 
Intuitive parking assist
(if equipped)
Press to enable/disable the
Intuitive parking assist.
Press and hold to change the
settings of the following item:
â– 
HUD (Head-up display) (if
equipped)
Press to enable/disable the
head-up display.
Press and hold to change the
settings of the following items:
â– 
RSA (Road Sign Assist) (if
equipped)
Press and hold to change the
settings of the following items:
â– 
Vehicle settings
Press and hold to change the
settings of the following items:
â– 
Meter settings
Press and hold to change the
settings of the following items:
*1: Selecting this item will only change the gadget.
*2: Selecting this item will turn the display of the gadget off.
Odometer/trip meter
â– Odometer
Displays the total distance the vehicle has been driven.
â– Trip meter A/trip meter B
Displays the distance the vehicle has been driven since the meter was last reset. Trip meters A and B can be used to record and display different distances independently.
To reset, display the desired trip meter and press and hold the "ODO/ TRIP" switch.
Eco-friendly driving information
â– Fuel consumption
Current fuel consumption
Displays the instantaneous current
fuel consumption.
Average fuel economy (after
start)
Displays the average fuel consumption
since engine ...
Suggestion function
Displays suggestions to the driver in the following situations. To select
a response to a displayed suggestion, use the meter control switches.
The suggestion function can be turned on/off.
â– S ...
Other materials:
Unexpected pedal reaction
Diagnosis Procedure
1.CHECK BRAKE PEDAL STROKE
Check brake pedal stroke. Refer to BR-15, "Adjustment".
Is the stroke too big?
YES >>
Bleed air from brake line and hose. Refer to BR-17,
"Bleeding Brake System".
Check brake pedal, brake booster, and maste ...
Floor trim
Exploded View
Floor trim
Harness protector
Front floor spacer (RH)
Front floor spacer (LH)
Rear floor spacer (LH)
Rear floor spacer (RH)
Column hole cover
Pawl
Front
Removal and Installation
REMOVAL
Remove front seat assemblies. Refer to the following.
Refer to S ...
P0863 TCM Communication
DTC Logic
DTC DETECTION LOGIC
DTC
CONSULT screen terms
(Trouble diagnosis content)
DTC detection condition
Possible causes
P0863
TCM COMMUNICATION
(TCM Communication Circuit)
An error is detected at the initial CAN diagnosis of TCM.
TCM
DTC CONFIRMATIO ...
