Nissan Sentra Service Manual: Rear seat
Exploded View

- Rear seatback assembly (RH)
- Seatback striker
- Seatback latch release knob
- Seatback latch assembly
- Seatback silencer (RH)
- Rear seatback frame (RH)
- Seatback latch release knob finisher
- Rear seat bolster trim (RH)
- Rear seat bolster pad (RH)
- Rear seat bolster (RH)
- Seatback trim (RH)
- Seatback pad (RH)
- Seatback hinge bracket (RH)
- LATCH bracket (RH)
- Seat cushion assembly
- Seat cushion hook
- Seat cushion pad
- Seat cushion trim
- Seatback hinge bracket (center)
- LATCH bracket (LH)
- Seatback hinge bracket (LH)
- Armrest pivot bolt finisher
- Armrest pivot bolt
- Armrest hinge bracket
- Armrest bushing (LH)
- Armrest bushing (RH)
- Armrest assembly
- Armrest hinge finisher
- Seatback pad (LH)
- Seatback trim (LH)
- Rear seat bolster pad (LH)
- Rear seat bolster trim (LH)
- Rear seat bolster (LH)
- Rear seatback frame (LH)
- Seatback silencer (LH)
- Rear seatback assembly (LH)
Removal and Installation - Seat Cushion Assembly
REMOVAL
- Lift up the seat cushion assembly close to the front edge (B) to release
it from the seat cushion hooks (A)
(one for each side) and remove the seat cushion assembly.
Front

INSTALLATION
Installation is in the reverse order of removal.
Removal and Installation - 60:40 Split Seatback
REMOVAL
- Place the rear seatback assembly in the folded down position.
- Release the hook fasteners (A) in the lower corners of the rear
seatback assembly.
- Remove the rear seatback assembly bolts (B) from the seatback
hinge brackets (1), then remove the rear seatback assembly.

INSTALLATION
Installation is in the reverse order of removal.
- Tighten the rear seatback assembly bolts to specification. Refer to
SE-22, "Exploded View".
Removal and Installation - Armrest Assembly
REMOVAL
- Place the rear seatback assembly (LH) in the folded down position.
- Release the J-hook retainer (A) and unzip the seatback trim zippers
(B).

- Remove two nuts (A) and the armrest assembly.

INSTALLATION
Installation is in the reverse order of removal.
Removal and Installation - Rear Seat Bolster
REMOVAL
- Remove the seat cushion assembly. Refer to SE-23, "Removal and
Installation - Seat Cushion Assembly".
- Remove the seat belt from the seat belt guide.
- Remove the bolt at bottom of rear seat bolster.
- Lift the rear seat bolster to remove.
INSTALLATION
Installation is in the reverse order of removal.
- Tighten rear seat bolster bolt to specification. Refer to SE-22,
"Exploded View".
Removal and Installation - Seat Cushion Hook
REMOVAL
- Remove the seat cushion assembly. Refer to SE-23, "Removal and
Installation - Seat Cushion Assembly".
- Release the seat cushion hook pawls as shown and remove.
CAUTION:
Before removing/installing the seat cushion hook, check its orientation
(front/rear).

INSTALLATION
Installation is in the reverse order of removal.
Removal and Installation - Seatback Striker
REMOVAL
- Place the rear seatback assemblies (LH/RH) in the folded down position.
- Remove the top three clips of the rear seatback finisher and position
aside to access the seatback striker
bolts. Refer to INT-32, "Exploded View".
- Remove bolts (A) and the seatback strikers (1).
NOTE:
Rear seatback finisher removed for clarity.

INSTALLATION
Installation is in the reverse order of removal.
- Tighten the seatback striker bolts to specification. Refer to SE-22,
"Exploded View".
Removal and Installation - Seatback Hinge Bracket
REMOVAL
- Remove the rear seatback assemblies (LH/RH). Refer to SE-23, "Removal
and Installation - 60:40 Split
Seatback".
- Remove the seat cushion assembly. Refer to SE-23, "Removal and
Installation - Seat Cushion Assembly".
- Remove rear seatback hinge bracket bolts (A) and remove.
- Seatback hinge bracket (RH)
- Seatback hinge bracket (center)
- Seatback hinge bracket (LH)

INSTALLATION
Installation is in the reverse order of removal.
- Tighten the seatback hinge brackets to specification. Refer to SE-22,
"Exploded View".
Driver side
DRIVER SIDE : Exploded View
Driver side
Headrest
Headrest holder (locked)
Headrest holder (free)
Seatback silencer
Seatback trim
Seatback pad
Seat belt buckle
Seat ...
Other materials:
License lamp finisher
Exploded view
Rear view camera
Trunk lid opener request switch
License lamp finisher
Clip
Pawl
Removal and installation
Remove trunk lid finisher. Refer to INT-45, "Removal and Installation".
Disconnect the harness connector (A) from trunk lid opener
request swit ...
Accelerator pedal released position
learning
Description
Accelerator Pedal Released Position Learning is a function of ECM to learn
the fully released position of the
accelerator pedal by monitoring the accelerator pedal position sensor output
signal. It must be performed each
time harness connector of accelerator pedal position sensor ...
Precaution for Work
When removing or disassembling each component, be careful not to damage
or deform it. If a component
may be subject to interference, be sure to protect it with a shop cloth.
When removing (disengaging) components with a screwdriver or similar
tool, be sure to wrap the component
with a ...
В© 2014-2025 Copyright www.nisentra.com