Nissan Sentra B18 (2020-2025) Service Manual: P2616 Intake Camshaft Position Sensor

Nissan Sentra B18 (2020-2025) Service Manual / Engine / Work Procedure (After Replacing Electric Throttle Control Actuator) / Dtc/circuit Diagnosis / P2616 Intake Camshaft Position Sensor

Dtc Description

DTC Description

DTC DETECTION LOGIC

DTC	CONSULT screen terms (Trouble diagnosis content)	DTC detection condition
P2616	A camshaft posi signal B1 (“A” camshaft position signal output circuit high bank 1)	Diagnosis condition	Engine running at idle
		Signal (terminal)	Intake camshaft position sensor signal for electric intake valve timing control
		Threshold	The intake camshaft position sensor signal edge count is more than 4 counts per one camshaft rotation
		Diagnosis delay time	1 second

POSSIBLE CAUSE

Harness or connectors [Intake camshaft position sensor signal circuit for electric intake valve timing control is open or shorted.]

FAIL-SAFE

Engine Control System

Engine operating condition in fail-safe mode
Fail safe mode		Nissan Sentra Vehicle behavior
Device fix mode		This mode fixes the electric IVT motor and the EVT control solenoid valve in the reference position. The intake manifold runner control valve motor is turned OFF (intake manifold runner control valve opens).
Combustion control mode	Stratified charge combustion control at starting	No stratified charge combustion at starting (cold start).
Others		ECM stops the electric valve timing control. (The camshaft returns to the position of most retard angle.)

Idle Start/Stop System

When a DTC is detected, the start/stop indicator lamp blinks slowly and the idle start/stop system operation is prohibited.

When ECM detects error while operating the idle start/stop system, ECM restarts the engine.

Confirmation Procedure

Confirmation Procedure

CHECK DTC PRIORITY

If DTC P2616 is displayed with DTC P0340, first perform the confirmation procedure (trouble diagnosis) for DTC P0340.

Is DTC P0340 detected?
YES >>
Perform diagnosis of applicable. Refer to DTC Description.
NO >>
GO TO 2.
PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the turn ignition switch OFF and wait at least 10 seconds before conducting the next test.

>>
GO TO 3.
PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine and wait at least 5 seconds.
2. Check 1st trip DTC.
Is DTC P2616 detected?
YES >>
Refer to DTC Diagnosis Procedure.
NO-1 >>
To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2 >>
Confirmation after repair: INSPECTION END

Dtc Diagnosis Procedure

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P2616 is displayed with DTC P0340, first perform the confirmation procedure (trouble diagnosis) for DTC P0340.

Is DTC P0340 detected?
YES >>
Perform diagnosis of applicable. Refer to DTC Description.
NO >>
GO TO 2.

CHECK INTAKE CAMSHAFT POSITION (CMP) SENSOR SIGNAL CIRCUIT FOR ELECTRIC INTAKE VALVE TIMING CONTROL

Turn ignition switch OFF.
Disconnect ECM harness connector and electric intake valve timing control module harness connector.

Check the continuity between ECM harness connector and electric intake valve timing control module harness connector.

ECM		Electric intake valve timing control module		Continuity
Connector	Terminal	Connector	Terminal	Continuity
F24	25	F80	37	Existed

Also check harness for short to power and short to ground.

Is the inspection result normal?

YES >>

INSPECTION END

NO >>

Repair or replace error-detected parts.

P2615 Intake Camshaft Position Sensor

Dtc Description DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble ...

P2617 Crankshaft Position Sensor

Dtc Description DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms ( ...

Other materials:

P34af Electric Intake Valve Timing Control Position Sensor
Dtc Description DTC Description DTC DETECTION LOGIC DTC CONSULT screen terms (Trouble diagnosis content) DTC detection conditi ...

P0181 FTT Sensor
DTC Logic DTC DETECTION LOGIC DTC No. CONSULT screen terms (Trouble diagnosis content) DTC detecting condition Possible cause P0181 FTT SENSOR (Fuel temperature sensor ″A″ circuit range/performance) A) Rationally incorrect voltage from the ...

Front wiper does not operate
Description The front wiper does not operate under any operation conditions Diagnosis procedure Regarding wiring diagram information, refer to ww-24, "wiring diagram - with intelligent key" or ww-29, "wiring diagram - without intelligent key". 1. Check wiper relay operatio ...