Nissan Sentra B18 (2020-2025) Service Manual / Engine / Work Procedure (After Replacing Electric Throttle Control Actuator) / Dtc/circuit Diagnosis / P2614 Intake Camshaft Position Sensor

Nissan Sentra B18 (2020-2025) Service Manual: P2614 Intake Camshaft Position Sensor

Dtc Description

DTC Description

DTC DETECTION LOGIC

DTC	CONSULT screen terms (Trouble diagnosis content)	DTC detection condition
P2614	A camshaft posi signal B1 (“A” camshaft position signal output circuit/open bank 1)	A	Diagnosis condition	Engine running at idle
			Signal (terminal)	Intake camshaft position sensor signal for electric intake valve timing control
			Threshold	The signal voltage of intake camshaft position sensor is less than 1.0 V
			Diagnosis delay time	1 second
		B	Diagnosis condition	Engine running at idle
			Signal (terminal)	Intake camshaft position sensor signal for electric intake valve timing control
			Threshold	The signal voltage of intake camshaft position sensor is more than 5.8 V
			Diagnosis delay time	1 second

POSSIBLE CAUSE

Harness or connectors [Intake camshaft position sensor signal circuit for electric intake valve timing control is open or shorted.]

FAIL-SAFE

Engine Control System

Engine operating condition in fail-safe mode
Fail safe mode		Nissan Sentra Vehicle behavior
Device fix mode		This mode fixes the electric IVT motor and the EVT control solenoid valve in the reference position. The intake manifold runner control valve motor is turned OFF (intake manifold runner control valve opens).
Combustion control mode	Stratified charge combustion control at starting	No stratified charge combustion at starting (cold start).
	Idle speed control	Stops feedback control of idle speed and controls with specified speed.
	Recovery speed control at decelerating	Stops recovery speed control by the fuel cut at decelerating and controls with specified speed.
	Idle neutral control	Stops idle neutral control.
Others		ECM stops the electric valve timing control. (The camshaft returns to the position of most retard angle.)

Idle Start/Stop System

When a DTC is detected, the start/stop indicator lamp blinks slowly and the idle start/stop system operation is prohibited.

When ECM detects error while operating the idle start/stop system, ECM restarts the engine.

Confirmation Procedure

Confirmation Procedure

CHECK DTC PRIORITY

If DTC P2614 is displayed with DTC P0340, first perform the confirmation procedure (trouble diagnosis) for DTC P0340.

Is DTC P0340 detected?
YES >>
Perform diagnosis of applicable. Refer to DTC Description.
NO >>
GO TO 2.
PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the turn ignition switch OFF and wait at least 10 seconds before conducting the next test.

>>
GO TO 3.
PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON and wait at least 5 seconds.
2. Start the engine and wait at least 5 seconds.
3. Check 1st trip DTC.
Is DTC P2614 detected?
YES >>
Refer to DTC Diagnosis Procedure.
NO-1 >>
To check malfunction symptom before repair: Refer to Intermittent Incident.
NO-2 >>
Confirmation after repair: INSPECTION END

Dtc Diagnosis Procedure

DTC Diagnosis Procedure

CHECK DTC PRIORITY

If DTC P2614 is displayed with DTC P0340, first perform the confirmation procedure (trouble diagnosis) for DTC P0340.

Is DTC P0340 detected?
YES >>
Perform diagnosis of applicable. Refer to DTC Description.
NO >>
GO TO 2.

CHECK INTAKE CAMSHAFT POSITION (CMP) SENSOR SIGNAL CIRCUIT FOR ELECTRIC INTAKE VALVE TIMING CONTROL

Turn ignition switch OFF.
Disconnect ECM harness connector and electric intake valve timing control module harness connector.

Check the continuity between ECM harness connector and electric intake valve timing control module harness connector.

ECM		Electric intake valve timing control module		Continuity
Connector	Terminal	Connector	Terminal	Continuity
F24	25	F80	37	Existed

Also check harness for short to power and short to ground.

Is the inspection result normal?

YES >>

INSPECTION END

NO >>

Repair or replace error-detected parts.

 P2610 Ecm Internal Timer

Dtc Description DTC Description This ECM contains a timer and measures time between an ignition switch OFF and the next ignition switch ON. This enables the judging of the state...

 P2b95 Cold Start Control

Dtc Description DTC Description ECM controls fuel injection timing and fuel injection quantity when engine is started with the engine cold. This control promotes the activation ...

Other materials:

Srs Air Bag. Precaution. Precautions
Precautions Precaution for Supplemental Restraint System (srs) "air Bag" and "seat Belt Pre-Tensioner" Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-T ...

Preparation. Preparation
Preparation Special Service Tool Special Service Tool The actual shape of the tools may differ from those illustrated here. Tool number (TechMate No.) Tool name ...

Door Does Not Lock/unlock with Door Request Switch and Intelligent Key
Description Description All doors do not lock/unlock using door request switch or trunk does not open using trunk opener request switch or Intelligent Key button. SYMPTOM TABLE (BOTH INTELLIGENT KEYS HAVE THE SAME SYMPTOMS) ...